command output to variable assignment and screen simultaneously
Hello Folks,
I have a script that runs a command (rsync) that sometimes takes a long time to complete and produces diagnostic output on stdout as it runs.
I am currently capturing this output in a variable and using it further in the script. I would like to continue to capture this output in a variable, but also display the output to the screen as it is produced from the command.
I am looking for a way to do this without creating a file on the filesystem. I am using Posix Shell on HP/UX and BASH on Linux (but open to other possibilities if necessary).
Currently I am doing this:
Any suggestions will be appreciated,
HI ,
I forgot to redirect my op to a file.The op which is quite huge , thus printed on the screen.However bcoz of the limited viewing in the screenI can not see the whole of the output..
Is there anyway I can see the full op.My run takes half a day for finnishing ..So I am refraining... (1 Reply)
Hi folks,
Please advise which command/command line shall I run;
1) to display the command and its output on console
2) simultaneous to save the command and its output on a file
I tried tee command as follows;
$ ps aux | grep mysql | tee /path/to/output.txt
It displayed the... (7 Replies)
Hi Gurus,
I am having 2 parameters as below
parm1=value1
parm2=parm1
I want to evaluate parm1 value using eval echo \$$parm2 and later i want to assign this value to other variable which i will be using in if statement like :
if ]; then
do this.......
fi
could you please suggest... (5 Replies)
Hi,
I want to use zenity --progress and also put the output to the terminal.
I tried using the tee command but that puts the output to the terminal first and then shows the zenity progress dialog.
Take the normal example by the gnome manual:
(
echo "10" ; sleep 1
... (0 Replies)
BACK STORY:
I have a script build.py . (It's for creating the ISO file for a special edition of Swift Linux.) This build.py script executes the mintConstructor.py script that I use to modify the Regular Swift Linux ISO to get the special edition Swift Linux ISO. The lines of the script that... (2 Replies)
Hi,
I'd like to redirect the STDOUT output from my script to a file and simultaneously display it at a console.
I've tried this command:
myscript.sh | tail -f
However, it doesn't end after the script finishes running
I've also tried this:
myscript.sh | tee ~/results.txt
But it writes... (3 Replies)
Hi Folks,
I'm looking to figure something out in an existing script I'm trying to understand.
the command in question(on a Solaris Box using KSH) is: WORKDIR=/tmp/namereplaced.exec.$$.$RANDOM
Now, I know it's setting the $workdir environmental variable...
And I understand most of... (2 Replies)
Hi there,
I'm a newbie to Unix (taking a course in it right now) and I don't know how to do the following in bash:
I need to write a command to display information about the used and free space on the file system, showing only local file systems, and then send the output of the command to... (1 Reply)
I have a section of a script where I want to check a log file for a certain oracle error and if there is only one error (and it is ORA-39152) then I want to email that script is complete. Otherwise email failure and log.
Somehow with this while the log only has one error and it is ORA-39152, I... (5 Replies)
Discussion started by: cougartrace
5 Replies
LEARN ABOUT DEBIAN
slack.conf
slack.conf(5) File Formats Manual slack.conf(5)NAME
slack.conf - configuration file for slack
DESCRIPTION
The file /etc/slack.conf contains configuration information for slack(8) and its backends. It should contain one keyword-value pair per
line, separated by an '=' sign. Keywords must consist solely of capital letters and underscores. Values may take any appropriate format,
but must not begin with a space. Comments start with '#', and all text from the '#' to the end of a line is ignored. Trailing whitespace
on lines is ignored. Empty lines or lines consisting of only whitespace and comments are ignored.
Valid keywords are:
SOURCE The master source for slack roles. It can be in one of four forms:
o /path/to/dir
Use a local directory.
o somehost:/path/to/dir
Use given directory on a remote host via rsync over SSH.
o rsync://somehost/module
Use module on a remote rsyncd server (directly over the network).
o somehost::module
Use the rsync daemon protocol over SSH to the given host. See "USING RSYNC-DAEMON FEATURES VIA A REMOTE-SHELL CONNECTION" in
rsync(1)
All forms of SOURCE are passed directly to rsync, so you can do things like add "user@" before the host on any remote forms. For
more about what rsync can do, see its manual page, of course.
For the last form, however, we do a little magic. rsync treats the last two forms equivalently, so we overload the last form by
automatically passing "-e ssh" to rsync when we see it. This hack lets us tell slack to use this nice feature of rsync just using
the SOURCE config option.
ROOT The root filesystem into which to install slack roles. Usually '/'.
ROLE_LIST
The location of the role list, which lists the roles to be installed by default on each host.
This can be a path relative to the source, or can be an entirely separate location if it starts with a slash or a hostname (option-
ally preceeded by user@).
CACHE A local cache directory, used as a local mirror of the SOURCE.
STAGE A local staging directory, used as an intermediate stage when installing files.
BACKUP_DIR
A directory in which to keep dated backups for rollbacks.
EXAMPLE
A typical file might look like this:
# slack.conf configuration file
SOURCE=slack-master:/slack # source is on a remote
# host named "slack-master"
ROLE_LIST=slack-master:/roles.conf
ROOT=/
CACHE=/var/cache/slack
STAGE=/var/lib/slack/stage
BACKUP_DIR=/var/lib/slack/backups
FILES
/etc/slack.conf
SEE ALSO slack(8), rsync(1)File formats 2005-05-23 slack.conf(5)