09-24-2009
there are three disk they are
" Segate cheetah Model no: ST318406LC ultra3 SCSI 10k 18GB "
three disk are same disk
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT SUNOS
raidctl
raidctl(1M) System Administration Commands raidctl(1M)
NAME
raidctl - RAID hardware utility
SYNOPSIS
raidctl -c disk1 disk2
raidctl -d disk1
raidctl [-f] -F filename controller...
raidctl -l [controller...]
DESCRIPTION
The raidctl utility creates, deletes, or displays RAID volumes of the LSI1030 HW Raid controllers that include RAID support. The utility
also updates firmware/fcode/BIOS for both RAID and non-RAID controllers.
The raidctl utility requires privileges that are controlled by the underlying file-system permissions. Only privileged users can manipulate
the RAID system configuration. If a non-privileged user attempts to create or delete a RAID volume, the command fails with EPERM.
Without options, raidctl displays the current RAID configuration on all exisiting controllers.
OPTIONS
The following options are supported:
-c disk1 disk2 (for on board)
Create a mirror using disk1 and disk2. Replace the contents of disk2 with the contents of disk1. Specify disk1 and disk2 in canonical
form, for example, c0t0d0.
When you create a a RAID volume, the RAID volume assumes the identity of the first target in the disk pair (disk1). The second target
(disk2) disappears from the system. Therefore, the RAID volume appears as one disk.
To have a successful RAID creation, there must not already be a RAID configuration present on the specified controller. Additionally,
the secondary disk must not be mounted, as it has all its data erased and replaced with the primary disk's data.
-d disk1 (for on board)
Delete the RAID volume specified as disk1.
Specify disk1 in canonical form, for example, c0t0d0.
-f (for HBA)
Force an update. Do not prompt.
-F filename controller (for HBA)
Update the firmware running on the specified controller (controller).
-l [controller ...] (for on board)
List the system's RAID configuration. If controller is specified, list RAID configurations for controller.
Output from the -l lists the following information:
RAID Volume Displays logical RAID volume name.
RAID Status Displays RAID status as either RESYNCING (disks are syncing), DEGRADED RAID is operating with reduced functionality),
OK (operating optimally), or FAILED (non-functional).
RAID Disk Displays RAID disk name.
Disk Status Displays disk status as either OK or FAILED.
EXAMPLES
Example 1: Creating the RAID Configuration
The following command creates the RAID configuration:
# raidctl -c c0t0d0 c0t1d0
RAID Volume 'c0t0d0' created
Example 2: Displaying the RAID Configuration
The following command displays the RAID configuration:
# raidctl
RAID RAID RAID Disk
Volume Status Disk Status
----------------------------------------
c0t0d0 RESYNCING c0t0d0 OK
c0t1d0 OK
Example 3: Deleting the RAID Configuration
The following command deletes the RAID configuration:
# raidctl -d c0t0d0
RAID Volume 'c0t0d0' deleted
Example 4: Updating Flash Images on the Controller
The following command updates flash images on the controller:
# raidctl -F lsi1030.fw 0
Update flash image on controller 0? (y/N): y
Flash updated successfully
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 Invalid command line input.
2 Request operation failed.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
System Administration Guide: Basic Administration
SunOS 5.10 17 Aug 2004 raidctl(1M)