09-24-2009
i hav used tis command also but it's still not working dude........
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT OSF1
tis_rwlock_init
tis_rwlock_init(3) Library Functions Manual tis_rwlock_init(3)
NAME
tis_rwlock_init - Initializes a read-write lock object.
LIBRARY
Standard C Library (libc.so, libc.a)
SYNOPSIS
#include <tis.h>
int tis_rwlock_init(
tis_rwlock_t *lock);
STANDARDS
None
PARAMETERS
Address of a read-write lock object.
DESCRIPTION
This routine initializes a read-write lock object. The routine initializes the tis_rwlock_t structure that holds the object's lock states.
To destroy a read-write lock object, call the tis_rwlock_destroy(3) routine.
NOTE: The tis read-write lock has no relationship to the Single UNIX Specification, Version 2 (SUSV2, or UNIX98) read-write lock routines
(pthread_rwlock_init(3), etc). The tis_rwlock_t type, in particular, cannot be used with the pthread read-write lock functions; nor can a
pthread_rwlock_t type be used with the tis read-write lock functions.
RETURN VALUES
If an error condition occurs, this routine returns an integer value indicating the type of error. Possible return values are as follows:
Successful completion. The value specified by lock is not a valid read-write lock. Insufficient memory exists to initialize lock.
ERRORS
None
RELATED INFORMATION
Functions: tis_read_lock(3), tis_read_trylock(3), tis_read_unlock(3), tis_rwlock_destroy(3), tis_write_lock(3), tis_write_trylock(3),
tis_write_unlock(3)
Manuals: Guide to DECthreads and Programmer's Guide delim off
tis_rwlock_init(3)