Sponsored Content
Operating Systems Solaris Route new network interface Solaris 8 Post 302355370 by sreiniche on Tuesday 22nd of September 2009 12:12:25 PM
Old 09-22-2009
Route new network interface Solaris 8

Hi there,


I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add -net 192.168.4.0/24 -interface eri0


Could someone please help me ?
I've had a look into this forum and did not find answers that could match this case.
Thanks to forgive me if I've missed up something...


Below various outputs from (I believe) useful commands:
#ifconfig -a:
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 160.94.3.111 netmask fffffe00 broadcast 160.94.3.255
ether 0:3:baSmilie2a:db
eri0: flags=1000850<POINTOPOINT,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.4.5 netmask ffffff00
ether 0:3:baSmilie2a:db
#netstat -rn:
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ------ ---------
140.94.2.0 140.94.3.111 U 1 12794 ce0
224.0.0.0 140.94.3.111 U 1 0 ce0
default 140.94.2.1 UG 1 20913
127.0.0.1 127.0.0.1 UH 386828356 lo0

#route get 192.168.4.6:
route to: 192.168.4.6
destination: 192.168.4.6
mask: 255.255.255.255
interface: ce0
flags: <UP,DONE>
recvpipe sendpipe ssthresh rtt,ms rttvar,ms hopcount mtu expire
0 0 0 0 0 0 1500 0


TIA!
Stephane
 

9 More Discussions You Might Find Interesting

1. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

2. Solaris

Solaris 9 on x86- Can't detect network interface

Hi All, I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot. While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies

3. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

4. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

5. Solaris

Getting Network Interface details in solaris

Hi, /sbin/ifconfig -a when i login as guest user , output like below, lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet... (5 Replies)
Discussion started by: forumguest
5 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

8. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

9. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 04:17 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy