09-18-2009
Hello Forum.
After a cut of energy upon resuming the team with SCO Unix 5.0.5 tells me when I start in normal way when mounts the board of directors /or the following thing:
Possibly damaged file system. Mount failed. Not space left on device (error 28)
In another occasion I remain with this message:
"NOT PARTIAL TRANSACTION PENDING"
The rare thing is that if I start in way maintenance and I do a df -v I have available space.?
Some suggestion?
Many Thanks. Reply With Quote
Translation via
http://ets.freetranslation.com/
*****************************************
Start by running fsck /dev/u while in single user mode, that is, enter the root password instead of <ctrl>d on start up.
Unless you are truly out of space on /u, you should have enough free space to allow the mount when going to multi-user.
Comience corriendo fsck/dev/U mientras en solo modo de usuario, eso es, entra la contraseña de raíz en vez de <ctrl>D en empieza. A menos que usted sea sinceramente fuera del espacio en/U, usted debe tener suficiente liberta el espacio para permitir el monte al ir al multi-usuario.
9 More Discussions You Might Find Interesting
1. What is on Your Mind?
A warning...
I used to be a BT Broadband customer, but changed to Sky in February.
BT withdrew the service with the cutover and that was that.
But I've just checked my credit card statements, and they've billed me for the service again for the past two months! (2 Replies)
Discussion started by: prowla
2 Replies
2. Shell Programming and Scripting
Hola,
Genere un proceso en proC que me inserta registros a oracle, el cual ejecuto desde un shell en Unix. Por otro lado tengo un sqlldr que me hace el trabajo en un 25 % de tiempo que mi proceso en C.
Se que puedo ejecutar mi sqlldr desde un shell, pero no se como hacer, alguien tiene un... (0 Replies)
Discussion started by: marcoinxs
0 Replies
3. Shell Programming and Scripting
Saludos
Necesito utilizar SED para crear una herramienta que me facilite el trabajo. El objetivo es filtrar información de un log para que me muestre solamente los registros que contengan una determinada cadena. El formato de cada registro es el siguiente:
a) un registro puede contener varias... (1 Reply)
Discussion started by: antuan
1 Replies
4. AIX
a Continuacion les muestro el mensaje de erro al momento de levantar la cola de impresion en aix
si alguien me ouee ayudar al respecto
Message from root on r_manlan (UNKNOWN) ...
Message from queueing system:
: (WARNING) 0781-391 Perhaps the file is too large for the server to handle.... (1 Reply)
Discussion started by: jetb01
1 Replies
5. Linux
Since a couple of days i get the following message:
/etc/cron.daily/prelink:
/etc/cron.daily/prelink: line 47: 31091 Aborted /usr/sbin/prelink -av $PRELINK_OPTS >>/var/log/prelink.log 2>&1
Please find attached the prelink.log
Can anybody help me out please?
Thx a... (2 Replies)
Discussion started by: Jumping
2 Replies
6. Shell Programming and Scripting
Hola a todos, soy nuevo en el foro y también en programación Shell Script.
El problema es el siguiente:
necesito hacer un Script que busque todos los procesos del sistema y me muestre de forma jerárquica la cantidad de Bytes que ocupa cada una de las regiones del mapa de memoria de cada proceso.
... (1 Reply)
Discussion started by: cougar_rea
1 Replies
7. Shell Programming and Scripting
Hola a todos, soy nuevo en el foro y también en programación Shell Script.
El problema es el siguiente:
necesito hacer un Script que busque todos los procesos del sistema y me muestre de forma jerárquica la cantidad de Bytes que ocupa cada una de las regiones del mapa de memoria de cada... (1 Reply)
Discussion started by: cougar_rea
1 Replies
8. UNIX for Dummies Questions & Answers
Hola a todos, soy nuevo en el foro y también en programación Shell Script.
El problema es el siguiente:
necesito hacer un Script que busque todos los procesos del sistema y me muestre de forma jerárquica la cantidad de Bytes que ocupa cada una de las regiones del mapa de memoria de cada proceso.
... (1 Reply)
Discussion started by: cougar_rea
1 Replies
9. Shell Programming and Scripting
Hola. Tengo un problema. En un archivo tengo distintos campos y en alguno de ellos y en alguna linea me aparecen ******.
ej:
hola 0.1 ****** 85
adios 1.2 9650 23
gracias 2 ****** 54
bye 87 5666 89
hi ... (1 Reply)
Discussion started by: kekaes
1 Replies
LEARN ABOUT DEBIAN
vfstab
vfstab(4) File Formats vfstab(4)
NAME
vfstab - table of file system defaults
DESCRIPTION
The file /etc/vfstab describes defaults for each file system. The information is stored in a table with the following column headings:
device device mount FS fsck mount mount
to mount to fsck point type pass at boot options
The fields in the table are space-separated and show the resource name (device to mount), the raw device to fsck (device to fsck), the
default mount directory (mount point), the name of the file system type (FS type), the number used by fsck to decide whether to check the
file system automatically (fsck pass), whether the file system should be mounted automatically by mountall (mount at boot), and the file
system mount options (mount options). (See respective mount file system man page below in SEE ALSO for mount options.) A '-' is used to
indicate no entry in a field. This may be used when a field does not apply to the resource being mounted.
The getvfsent(3C) family of routines is used to read and write to /etc/vfstab.
/etc/vfstab can be used to specify swap areas. An entry so specified, (which can be a file or a device), will automatically be added as a
swap area by the /sbin/swapadd script when the system boots. To specify a swap area, the device-to-mount field contains the name of the
swap file or device, the FS-type is "swap", mount-at-boot is "no" and all other fields have no entry.
EXAMPLES
The following are vfstab entries for various file system types supported in the Solaris operating environment.
Example 1: NFS and UFS Mounts
The following entry invokes NFS to automatically mount the directory /usr/local of the server example1 on the client's /usr/local directory
with read-only permission:
example1:/usr/local - /usr/local nfs - yes ro
The following example assumes a small departmental mail setup, in which clients mount /var/mail from a server mailsvr. The following entry
would be listed in each client's vfstab:
mailsvr:/var/mail - /var/mail nfs - yes intr,bg
The following is an example for a UFS file system in which logging is enabled:
/dev/dsk/c2t10d0s0 /dev/rdsk/c2t10d0s0 /export/local ufs 3 yes logging
See mount_nfs(1M) for a description of NFS mount options and mount_ufs(1M) for a description of UFS options.
Example 2: pcfs Mounts
The following example mounts a pcfs file system on a fixed hard disk on an x86 machine:
/dev/dsk/c1t2d0p0:c - /win98 pcfs - yes -
The example below mounts a Jaz drive on a SPARC machine. Normally, the volume management daemon (see vold(1M)) handles mounting of remov-
able media, obviating a vfstab entry. If you choose to specify a device that supports removable media in vfstab, be sure to set the mount-
at-boot field to no, as below. Such an entry presumes you are not running vold.
/dev/dsk/c1t2d0s2:c - /jaz pcfs - no -
For removable media on a SPARC machine, the convention for the slice portion of the disk identifier is to specify s2, which stands for the
entire medium.
For pcfs file systems on x86 machines, note that the disk identifier uses a p (p0) and a logical drive (c, in the /win98 example above) for
a pcfs logical drive. See mount_pcfs(1M) for syntax for pcfs logical drives and for pcfs-specific mount options.
Example 3: CacheFS Mount
Below is an example for a CacheFS file system. Because of the length of this entry and the fact that vfstab entries cannot be continued to
a second line, the vfstab fields are presented here in a vertical format. In re-creating such an entry in your own vfstab, you would enter
values as you would for any vfstab entry, on a single line.
device to mount: svr1:/export/abc
device to fsck: /usr/abc
mount point: /opt/cache
FS type: cachefs
fsck pass: 7
mount at boot: yes
mount options:
local-access,bg,nosuid,demandconst,backfstype=nfs,cachedir=/opt/cache
See mount_cachefs(1M) for CacheFS-specific mount options.
Example 4: Loopback File System Mount
The following is an example of mounting a loopback (lofs) file system:
/export/test - /opt/test lofs - yes -
See lofs(7FS) for an overview of the loopback file system.
SEE ALSO
fsck(1M), mount(1M), mount_cachefs(1M), mount_hsfs(1M), mount_nfs(1M), mount_tmpfs(1M), mount_ufs(1M), swap(1M), getvfsent(3C)
System Administration Guide: Basic Administration
SunOS 5.10 21 Jun 2001 vfstab(4)