09-16-2009
Configure Sun Cluster
Hi,
I am configuring the sun cluster between two nodes. It is asking me to create a filesystem called globaldevices in root and mount it permanently. I created a new slice c0t0d0s3 and created a filesytem /globaldevices. How can I mount it permanently. I know we have to do it /etc/vfstab, but how do I give the entries there.
Help me out?
9 More Discussions You Might Find Interesting
1. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
2. Solaris
Hi Gurus,
For learning purpose, I have installed a single node cluster 3.2 on Solaris 10 for practice. Now I am welling to create two non-global zone and create them as a fail over. Will appreciate your help and assistance.
Thanks (3 Replies)
Discussion started by: newadmin
3 Replies
3. Solaris
hi
can u please send me how to configure cluster in x86 machines. i am using VM ware. Is there any difference in X86 and SPARC cluster installations
please help me
thaks to all (1 Reply)
Discussion started by: sijocg
1 Replies
4. Solaris
Hi,
I am getting these messages constantly at random times there is not visible impact but would like to know what these messages mean?
Cluster.RGM.rgmd: resource group
on node change to RG_ON_PENDING_R_RERT
Cluster.RGM.rgmd: resource group on node change to RG_ONLINE (1 Reply)
Discussion started by: xor
1 Replies
5. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
6. Solaris
Hi
I have a new mount point which is to added to to an existing resource group. I read many docs but I am not able to find the exact methods.
Could anyone help me pls. (1 Reply)
Discussion started by: ningy
1 Replies
7. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
8. Red Hat
HI
How can i configure fence_cisco_ucs with redhat cluster suite.
i was trying to configure fencing aganet with red ahat cluster suite
i issued command
# /usr/sbin/fence_vmware_soap -a 172.22.90.61 -l admin -p duc2Cisco -o reboot
then i got below error:
Failed: You have to... (0 Replies)
Discussion started by: bentech4u
0 Replies
9. Solaris
Running Sun Cluster v3.2 it appears. Two clustered physcial servers both running Solaris 10.
Both servers run a number of Oracle DBs etc. BUT I'm a bit concerned that its been set up but will never switch in the even of failure of one of the hosts?
Some of the cluster groups we've... (3 Replies)
Discussion started by: psychocandy
3 Replies
LEARN ABOUT OPENSOLARIS
scsetup
scsetup(1M) System Administration Commands scsetup(1M)
NAME
scsetup - interactive cluster configuration tool
SYNOPSIS
scsetup [-f logfile]
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
The scsetup command provides the following configuration capabilities, depending on what state the cluster is in when you issue the com-
mand:
o When you run the scsetup command at post-installation time, the command performs initial setup tasks, such as configuring quorum
devices and resetting the installmode property. If you did not use automatic quorum configuration when you created the cluster,
run the scsetup command immediately after the cluster is installed. Ensure that all nodes have joined the cluster before you run
the scsetup command and reset the installmode property.
If you used automatic quorum configuration when you created the cluster, you do not need to run the scsetup command after clus-
ter installation. The automatic quorum configuration feature also resets the installmode property of the cluster.
o When you run the command during normal cluster operation, the scsetup command provides a menu-driven utility. You can use this
utility to perform most ongoing cluster-administration tasks.
o When you issue the command from a node that is in noncluster mode, the scsetup utility provides a menu-driven utility for chang-
ing and displaying the private IP address range. You must reboot all nodes into noncluster mode before you start this form of
the scsetup utility.
You can issue the scsetup command from any node in the cluster.
You can use this command only in the global zone.
OPTIONS
The following options are supported:
-f logfile Specifies the name of a log file to which commands can be logged. If you specify this option, most command sets that
the scsetup utility generates are run and logged, or only logged, depending on user responses.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes.
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsczu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
Intro(1CL), cltelemetryattribute(1CL), cldevicegroup(1CL), clnode(1CL), clquorum(1CL), clreslogicalhostname(1CL), clresourcegroup(1CL),
clresourcetype(1CL), clressharedaddress(1CL), cluster(1CL),
Sun Cluster 3.2 18 Jul 2006 scsetup(1M)