hi all,
have a ksh script where i am doing a
but for some reason it only writes 15 lines wheres when i run the same command manually from command prompt it prints out 60 lines.
why is it not writing the full 60 lines to the file ??
Hello,
The last line of prstat shows load average.
I am unable to figure out what actually it is.
I have read the man pages and also googled, all for no use.
Can somebody help me, as to what should be the avg. load of the system for best performance and how is this load of prstat calculated. (6 Replies)
Hi,
How to redirect the output of prstat command to a file.
Ex:
I want to do like this
while :
do
prstat >> prs.log
sleep 5
done
is it possible ???? if No, then how can i proceed??
PLEASE HELP ME OUT FROM THIS :confused:
Thanks in advance
----------- (2 Replies)
Good Evening everyone,
I am confused about prstat O/P as it shows memory values which are different from actual value.Below is the O/P of prstat command and swap commands.
NPROC USERNAME SIZE RSS MEMORY TIME CPU
48 root 2113M 1590M 1.2% 45:09.39 32%
31 daemon ... (7 Replies)
Can someone please explain me the "TIME" field of the output of "prstat -p<pid>" command ? The man page says it is "The cumulative execution time for the process". Does it mean how many hrs:min:sec the process is running ? If so then I'm not getting the desired output.
Can someone pls help me in... (5 Replies)
hi all,
was trying to figure out how busy my app was by looking at the performance of the app server. did a 'prstat -s rss' command to find the app servers using most memory.
Found a command 'prstat -m' which is meant to show more details on each pid but the output of this command... (1 Reply)
Hi,
I want to fire the prstat command which should run fro 60 secs and get the report into a text file using a script.
I just know the command:
prstat -c >> log.txt
which will run until we stop it.
But i want the script to run only for 60 sec,print the output to text file and stop... (3 Replies)
Hi Expert,
I want to print CPU and Memory utilization into a text file. I am using "prstat -Z" to see the output on screen. When I run below command
prstat -Z | grep httpd | awk '{print$3} '>> output.txt
but it is not printing to file. Also I want to be below header on output
PID USERNAME ... (6 Replies)
need help with formatting output of command top and prstat. My requirment is to remove few columns and display remaining . But when i used awk to do that the output seems to be have gone vague, mixing the column values.
After using awk to print particular column the output seems to have lost... (1 Reply)
Hi how to send below prstat script output into table format and send through email?
prstat|awk '{ if ($9 >= 5) print $0 }' (17 Replies)
Discussion started by: tharmendran
17 Replies
LEARN ABOUT OSX
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS -raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO ppm(5)AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)