We have a problem on a Sparc Ultra 5 box when installing solaris.
We boot from the CD-ROM then go through the install procedure adding IP address, domain, routing details, hard disk layout etc.. The problem arises when asked for the 2nd CD at this point you do get the option to "skip"... (1 Reply)
Hi,
Have never run xntpd before. I have my ntp.conf file configured with server, trace file and drift file. I commented out the "broadcastclient" entry since I only want to get the time from a single source. Port 123 is in the /etc/services file for tcp and udp. Port 123 has been enabled in... (0 Replies)
hi experts,
i have some problem with my solaris 8 v890 server, is :
the server running process called SS7 below is example process :
PID STAT MODE HOST MUX OBJECT
384 ok LX|A USSDGmdn-1a spm/0 daemon
385 ok LX|A USSDGmdn-1a spm/2 ... (0 Replies)
Hi,
I have Solaris 9 installed on a SunFire V880. When the machine boots up, I get a message, "the X-server cannot be started on display:0".
I searched the forum for possible solution, however, they are not applicable to my problem for two reasons: either the platform is different or the... (6 Replies)
Hello
How can I check to see when nis server is starting? I look at /etc/rc2.d/ but I don't see it in there.
Every time we have power outage problem. I have to start autof service manual. So I think it might have to do with nis server services. (1 Reply)
hi!
my computer is...
system: Digital Personal Workstation 433a
Processor: Digital Alpha 21164, 433 MHz
Memory: 64 MB
Operating System: Digital Unix Console(SRM), Digital Unix V4.0D
That computer is used for radar display. Application run on Unix. I have a problem now. I can't boot dkc0... (2 Replies)
I seem to be having a very irritating problem with my Solaris 11 Express fileserver which I built for my small home business. The basic problem is that the system will hang or freeze about 20 seconds into booting up. Grub comes up fine, and I can select between pre-napp-it and current build. It... (13 Replies)
Is there a way to debug the startup on a VT100 running Solaris 5? I have a problem related to file attributes that are resetting to there prior settings when the machine reboots. (3 Replies)
Hi all,
I have a server in maintenance mode and need to boot it up. Its due to a broken service "RepX".
I need to stop the service from trying to start at boot up but i can't find where it is booting up from... it is not in any of the rcX.d directories and the two locations i have found it... (6 Replies)
Hi,
I've installed dynatrace on a SunOS(5.10) & I need to update its agent path in JVM start up script.
Where can I find or which script starts JVM?
Some Details here :
Java location : /<server location>/oracle/forms/FRHome_1/jdk/jre/bin
Please help me in this. I did some research... (2 Replies)
Discussion started by: raj100
2 Replies
LEARN ABOUT CENTOS
locale::codes::langvar
Locale::Codes::LangVar(3) User Contributed Perl Documentation Locale::Codes::LangVar(3)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('arevela','alpha');
$lvar = code2langvar('arevela',LOCALE_LANGVAR_ALPHA);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.3 2013-04-12 Locale::Codes::LangVar(3)