09-08-2009
unable to mount metaset on cluster node
Dear all,
I have created a shared metaset(500gb) having 3 hosts in which 2 hosts are in cluster and 1 is non cluster. I have taken the ownership in cluster node from non cluster node but the problem is i am unable to mount the file system it is giving error "/dev/md/eccdb-ds/d100 or /eccdb-ds device not found "
here if i take the ownership back non cluster mode now it is mounted.
hi all can u plz find a solution for it.
Regards
spandan
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello,
Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node:
# rsh <name> "command"
I have to implement this script on all the clusters of my company (a lot of...).
Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies
2. HP-UX
Need help guys!
when running cmrunnode batch i'm getting this error
cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies
3. High Performance Computing
hi,
i am trying to setup a 2 node cluster environment. following is what i have;
1. 2 x sun ultra60 - 450MHz procs, 1GB RAM, 9GB HDD, solaris 10
2. 2 x HBA cards
3. 2 x Connection leads to connect ultra60 with D1000
4. 1 x D1000 storage box.
5. 3 x 9GB HDD + 2 x 36GB HDD
first of all,... (1 Reply)
Discussion started by: solman17
1 Replies
4. Solaris
I now the logical name and Virtual IP of the cluster.
How can I find the active sun cluster node without having root access? (3 Replies)
Discussion started by: sreeniatbp
3 Replies
5. HP-UX
Hello,
Is there any way to identify the active node in a HP-UX cluster without root privileges? (3 Replies)
Discussion started by: psimoes79
3 Replies
6. Solaris
Hi Guys
i have two servers which are n cluster prd1 and prd2.. I already have a metaset configured in it..My job was to create a 1.8 tb LUN in my storage which is having Hardware raid5 pre-configured..i Created 1.8 tb with raid 5 in my storage and it got detected in both t servers prd1... (4 Replies)
Discussion started by: madanmeer
4 Replies
7. Emergency UNIX and Linux Support
Hi Guys
i have two servers which are n cluster prd1 and prd2.. I already have a metaset configured in it..My job was to create a 1.8 tb LUN in my storage which is having Hardware raid5 pre-configured..i Created 1.8 tb with raid 5 in my storage and it got detected in both t servers... (5 Replies)
Discussion started by: madanmeer
5 Replies
8. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
9. AIX
Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies
10. HP-UX
Hi,
We have HP UX service guard cluster on OS 11.23. Recently 40+ LUNs presented to both nodes by SAN team but I was asked to mount them on only one node. I created required VGs/LVs, created VxFS and mounted all of them and they are working fine. Now client requested those FS on 2nd node as... (4 Replies)
Discussion started by: prvnrk
4 Replies
LEARN ABOUT DEBIAN
mkqdisk
mkqdisk(8) Quorum Disk Management mkqdisk(8)
NAME
mkqdisk - Cluster Quorum Disk Utility
WARNING
Use of this command can cause the cluster to malfunction.
SYNOPSIS
mkqdisk [-?|-h] | [-L] | [-f label] [-c device -l label] [-d [-d ...]]
DESCRIPTION
The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.
OPTIONS
-c device -l label
Initialize a new cluster quorum disk. This will destroy all data on the given device. If a cluster is currently using that device
as a quorum disk, the entire cluster will malfunction. Do not run this on an active cluster when qdiskd is running. Only one
device on the SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
RAID array is used for quorum disk redundancy). The label can be any textual string up to 127 characters - and is therefore enough
space to hold a UUID created with uuidgen(1).
-f label
Find the cluster quorum disk with the given label and display information about it.
-L Display information on all accessible cluster quorum disks.
-d Increase debugging level. Specify multiple times for more information. Currently, specifying more than twice has no effect.
SEE ALSO
qdisk(5), qdiskd(8), uuidgen(1)
July 2006 mkqdisk(8)