I want to print between the range two patterns if a particular pattern is present in between the two patterns. I am new to Unix. Any help would be greatly appreciated.
e.g.
Pattern1
Bombay
Calcutta
Delhi
Pattern2
Pattern1
Patna
Madras
Gwalior
Delhi
Pattern2
Pattern1... (2 Replies)
Hi,
My input has much more lines, but few of them are below
pin(IDF) {
direction : input;
drc_pinsigtype : signal;
pin(SELDIV6) {
direction : input;
drc_pinsigtype : ... (3 Replies)
Hi all,
on Solaris 10, I'd like to print a range of lines starting at pattern but also including the very first line before pattern.
the following doesn't print the range starting at pattern and going down to the end of file: cat <my file> | sed -n -e '/<pattern>{x;p;}/'
I need to include the... (1 Reply)
Hi,
I have a file as below
This is the line one
This is the line two
<\XMLTAG>
This is the line three
This is the line four
<\XMLTAG>
Output of the SED command need to be as below.
This is the line one
This is the line two
<\XMLTAG>
Please do the need to needful to... (4 Replies)
Hi all,
I have been searching all over Google but I am unable to find a solution for a particular result that I am trying to achieve.
Consider the following input:
1
2
3
4
5
B4Srt1--Variable-0000
B4Srt2--Variable-1111
Srt
6
7
8
9
10
End (3 Replies)
I am trying to combine lines with these conditions:
1. First line starts with text of "libname VALUE db2 datasrc" where VALUE can be any text.
2. If condition1 is met then continue to combine lines through a line that ends with a semicolon.
3. Ignore case when matching patterns and remove any... (5 Replies)
In the awk below, what I am attempting to do is check each line in the tab-delimeted input, which has ~20 lines in it, for a keyword
SVTYPE=Fusion. If the keyword is found I am splitting $3 using the . (dot) and reading the portion before and after the dot in an array a.
If it does have that... (12 Replies)
I have been searching and trying to come up with an awk that will perform the following on a
converted text file (original is a pdf).
1. Since the first two lines are (begin with) text they are removed
2. if $1 is a number then all text is merged (combined) into one line until the next... (3 Replies)
In the awk piped to sed below I am trying to format file by removing the odd xxxx_digits and whitespace after, then move the even xxxx_digit to the line above it and add a space between them. There may be multiple lines in file but they are in the same format. The Filename_ID line is the last line... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)