I want to print between the range two patterns if a particular pattern is present in between the two patterns. I am new to Unix. Any help would be greatly appreciated.
e.g.
Pattern1
Bombay
Calcutta
Delhi
Pattern2
Pattern1
Patna
Madras
Gwalior
Delhi
Pattern2
Pattern1... (2 Replies)
Hi,
My input has much more lines, but few of them are below
pin(IDF) {
direction : input;
drc_pinsigtype : signal;
pin(SELDIV6) {
direction : input;
drc_pinsigtype : ... (3 Replies)
Hi all,
on Solaris 10, I'd like to print a range of lines starting at pattern but also including the very first line before pattern.
the following doesn't print the range starting at pattern and going down to the end of file: cat <my file> | sed -n -e '/<pattern>{x;p;}/'
I need to include the... (1 Reply)
Hi,
I have a file as below
This is the line one
This is the line two
<\XMLTAG>
This is the line three
This is the line four
<\XMLTAG>
Output of the SED command need to be as below.
This is the line one
This is the line two
<\XMLTAG>
Please do the need to needful to... (4 Replies)
Hi all,
I have been searching all over Google but I am unable to find a solution for a particular result that I am trying to achieve.
Consider the following input:
1
2
3
4
5
B4Srt1--Variable-0000
B4Srt2--Variable-1111
Srt
6
7
8
9
10
End (3 Replies)
I am trying to combine lines with these conditions:
1. First line starts with text of "libname VALUE db2 datasrc" where VALUE can be any text.
2. If condition1 is met then continue to combine lines through a line that ends with a semicolon.
3. Ignore case when matching patterns and remove any... (5 Replies)
In the awk below, what I am attempting to do is check each line in the tab-delimeted input, which has ~20 lines in it, for a keyword
SVTYPE=Fusion. If the keyword is found I am splitting $3 using the . (dot) and reading the portion before and after the dot in an array a.
If it does have that... (12 Replies)
I have been searching and trying to come up with an awk that will perform the following on a
converted text file (original is a pdf).
1. Since the first two lines are (begin with) text they are removed
2. if $1 is a number then all text is merged (combined) into one line until the next... (3 Replies)
In the awk piped to sed below I am trying to format file by removing the odd xxxx_digits and whitespace after, then move the even xxxx_digit to the line above it and add a space between them. There may be multiple lines in file but they are in the same format. The Filename_ID line is the last line... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT MOJAVE
gllinestipple
GLLINESTIPPLE(3G)GLLINESTIPPLE(3G)NAME
glLineStipple - specify the line stipple pattern
C SPECIFICATION
void glLineStipple( GLint factor,
GLushort pattern )
PARAMETERS
factor Specifies a multiplier for each bit in the line stipple pattern. If factor is 3, for example, each bit in the pattern is used
three times before the next bit in the pattern is used. factor is clamped to the range [1, 256] and defaults to 1.
pattern Specifies a 16-bit integer whose bit pattern determines which fragments of a line will be drawn when the line is rasterized. Bit
zero is used first; the default pattern is all 1's.
DESCRIPTION
Line stippling masks out certain fragments produced by rasterization; those fragments will not be drawn. The masking is achieved by using
three parameters: the 16-bit line stipple pattern pattern, the repeat count factor, and an integer stipple counter s.
Counter s is reset to 0 whenever glBegin is called, and before each line segment of a glBegin(GL_LINES)/glEnd sequence is generated. It is
incremented after each fragment of a unit width aliased line segment is generated, or after each i fragments of an i width line segment are
generated. The i fragments associated with count s are masked out if
pattern bit (s / factor) mod 16
is 0, otherwise these fragments are sent to the frame buffer. Bit zero of pattern is the least significant bit.
Antialiased lines are treated as a sequence of 1 * width rectangles for purposes of stippling. Whether rectagle s is rasterized or not
depends on the fragment rule described for aliased lines, counting rectangles rather than groups of fragments.
To enable and disable line stippling, call glEnable and glDisable with argument GL_LINE_STIPPLE. When enabled, the line stipple pattern is
applied as described above. When disabled, it is as if the pattern were all 1's. Initially, line stippling is disabled.
ERRORS
GL_INVALID_OPERATION is generated if glLineStipple is executed between the execution of glBegin and the corresponding execution of glEnd.
ASSOCIATED GETS
glGet with argument GL_LINE_STIPPLE_PATTERN
glGet with argument GL_LINE_STIPPLE_REPEAT
glIsEnabled with argument GL_LINE_STIPPLE
SEE ALSO
glLineWidth, glPolygonStipple
GLLINESTIPPLE(3G)