Sponsored Content
Operating Systems Solaris Solaris 10 Speed and Duplex Settings: bge Post 302349316 by brialt1 on Monday 31st of August 2009 04:12:45 PM
Old 08-31-2009
What I posted before are my changes, the original file includes only commented out material and the following:

Code:
#########################################################################
#
# The property below represents the list of subsystem vendor/device pairs
# with which driver operation is supported.  This list will be updated and
# extended as new subsystems are validated ...
#
bge-known-subsystems    = 0x108e1647,
                          0x108e1648,
                          0x108e16a7,
                          0x108e16a8,
                          0x17c20010,
                          0x17341013,
                          0x101402a6,
                          0x10f12885,
                          0x17c20020,
                          0x10b71006,
                          0x10280109,
                          0x1028865d,
                          0x0e11005a,
                          0x103c12bc;
#########################################################################

 

10 More Discussions You Might Find Interesting

1. Solaris

Duplex Settings

Hi All I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that. How do I: 1. Check the duplex settings on my eri0 card? 2. Set the... (3 Replies)
Discussion started by: saabir
3 Replies

2. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies

3. HP-UX

command to change duplex settings..

Hi Folks, I want the command to change the duplex settings of a HP-UX server. Thanks in advance. Sagar. (2 Replies)
Discussion started by: sag71155
2 Replies

4. Solaris

gigabit - fix speed/duplex on the switch ? or autoneg ?

Hi there We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is. As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

5. UNIX for Advanced & Expert Users

How to set full duplex for solaris 5.5

I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5. #ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies

6. Infrastructure Monitoring

How to find the duplex speed on Windows

Hi, In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this? Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies

7. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies

8. AIX

How to change Speed Duplex

How to change Speed Duplex ! How to change Speed Duplex by command chdev -P -l ent1 -a media_speed=1000_Full_Duplex How to change Speed Duplex by Smitty . smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies

9. AIX

Connected and Running with half duplex speed

VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good. Other ethernet adapter in the VIO server are connected and running in Full duplex speed. Please help me find why this shared... (4 Replies)
Discussion started by: mugunthanvh
4 Replies

10. Shell Programming and Scripting

Need script help for monitoring duplex settings

So I have a server I am trying to set up a script to send a Wall message notifying of my eth0 nic being set to 100 half duplex instead of 100 full duplex. I know I am trying to read from /etc/sysconfig/network/ifcfg-eth0 to pull the parameters STARTMODE=onboot BOOTPROTO=static... (6 Replies)
Discussion started by: lutador72
6 Replies
Intro_jfp(7)						   Device and Network Interfaces					      Intro_jfp(7)

NAME
Intro_jfp, intro_jfp - introduction to JFP special files DESCRIPTION
This section describes various device and network interfaces available on the system. The types of interfaces described include character and block devices, STREAMS modules, network protocols, file systems, and ioctl requests for driver subsystems and classes. This section contains the following major collections:(7I) This section describes ioctl requests which apply to a class of drivers or subsystems. Ioctl requests relevant to only a specific device are described on the man page for that device. The page for the device in question should still be examined for exceptions to the ioctls listed in section 7I.(7M) This section describes STREAMS modules. Note that STREAMS drivers are discussed in section 7D. streamio(7I) contains a list of ioctl requests used to manipulate STREAMS modules and interface with the STREAMS framework. Ioctl requests specific to a STREAMS module will be discussed on the man page for that module. SEE ALSO
add_drv(1M), rem_drv(1M), intro(2), ioctl(2), socket(3SOCKET), driver.conf(4), intro(7), arp(7P), icmp(7P), inet(7P), ip(7P), mtio(7I), st(7D), streamio(7I), tcp(7P), udp(7P) STREAMS Programming Guide Writing Device Drivers LIST
Name Description Intro_jfp(7) introduction to JFP special files jaio(7I) interface to Japanese I/O modules jconv7(7M) code conversion STREAMS module (7-bit JIS/Japanese EUC) jconv8(7M) code conversion STREAMS module (8-bit JIS/Japanese EUC) jconvrs(7M) code conversion STREAMS module (Japanese EUC/PC kanji) jconvru(7M) code conversion STREAMS module (Japanese EUC/UTF--8) jconvs(7M) code conversion STREAMS module (PC kanji/Japanese EUC) jconvu(7M) code conversion STREAMS module (UTF-8/Japanese EUC) SunOS 5.10 7 Dec 1999 Intro_jfp(7)
All times are GMT -4. The time now is 05:47 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy