08-28-2009
In Solaris 10, mpxio is enabled in /kernel/drv/fp.conf.
10 More Discussions You Might Find Interesting
1. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
2. Solaris
Hello!
I have several disks discovered using iscsi protocol.
There disks are represented in OS like c2txd0 .
logs:
Is it possible to change drive path, for example, from c2t6d0 to c2t7d0?
It's important for me because I have to install oracle RAC on RAW devices.
NIck (0 Replies)
Discussion started by: skelet
0 Replies
3. UNIX for Advanced & Expert Users
I am running Solaris 10 on a V490. I have Dell EqualLogic SAN attached.
I would like to take full advantage of the iSCSI initiator.
I have a primary network interface and IP addresses for all four SAN ports. Since the four ports are SUN GigaSwift (legacy), I cannot utilize dladm, so I downloaded... (2 Replies)
Discussion started by: KSFlyer
2 Replies
4. UNIX for Dummies Questions & Answers
how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies
5. Solaris
I have been running some tests with solaris mpxio, dual-pathed to HDS SAN storage.
When I take a path offline, Solaris recognised this and a path is shown as offline in luxadm display <device>. However, it does not recover on reinstatement of the path until I run cfgadm -al.
Any ideas?
Phil (3 Replies)
Discussion started by: UKPhil
3 Replies
6. Solaris
Im not able to turn the multipath off on the solaris s10 X86...since im on FC boot..
if i disable multipath , from /kernel/drv/iscsi.conf then im not able to boot the machine.:wall:
Is there any other go or any suggestions . (2 Replies)
Discussion started by: gowtham.varma
2 Replies
7. Solaris
Hi,
I have an Oracle/Sun T3-2 Server with a duel SAS controller Fujitsu DX60 array attached.
I have 2 x SAS HBA's in the T3-2. One HBA cabled to CM0 and one HBA cabled to CM1 of the array.
The array is setup with one RAID GROUP and one VOLUME and one LUN
In Solaris I can see one device... (4 Replies)
Discussion started by: general_lee
4 Replies
8. Solaris
hi to all
i've done that steps, but i was not completely successful:
sudo pkg install group/feature/storage-server
sudo svcadm enable stmf
sudo zfs create -V 1g rpool/LUN1
sudo stmfadm create-lu /dev/zvol/rdsk/rpool/LUN1
sudo stmfadm list-lu ... (4 Replies)
Discussion started by: jm83
4 Replies
9. Solaris
Hi Community,
I am facing one issue related storage accessing from solaris 10 machine(M5000). it was working fine then we shifted to another site. the only change on that site is FC switch.
The issue i am facing is from solaris machine i can able to see the LUN, it;s only a test lun of 30... (17 Replies)
Discussion started by: bentech4u
17 Replies
10. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
LEARN ABOUT DEBIAN
ql-hba-snapshot
ql-hba-snapshot(8) System Administration ql-hba-snapshot(8)
NAME
ql-hba-snapshot - display specific information of the QLogic HBA.
SYNOPSIS
ql-hba-snapshot <Host number> [OPTIONS]
DESCRIPTION
FC HBA Snapshot Utility
This utility displays the details of the QLogic HBA attached to the system. It uses one of the two file systems for scanning: proc or
sysfs.
<Host number> | <-a/--all> [optional]
Provide the <HOST NUMBER> to display the detailed information of the HBA. With no option specified, general information of all
hosts will be displayed. Ex. # /usr/sbin/ql-hba-snapshot <Host Number> # /usr/sbin/ql-hba-snapshot --procfs <Host Number> (For
procfs)
-h, --help
Prints the help message. Ex. # /usr/sbin/ql-hba-snapshot --help
-hl, --hostlist
This option displays the list of QLogic hosts (HBAs) connected to this system. The <HOST NUMBER> can be obtained by using following
command Ex. # /usr/sbin/ql-hba-snapshot --hostlist
-p, --parameters
This option displays the command line parameters that can be passed to the QLogic HBA driver. Ex. # /usr/sbin/ql-hba-snapshot
--parameters <Host Number>
-s, --statistics
This option displays the statistical information for specified host. Stastics option is only supported in "sysfs" based scan. Ex.
# /usr/sbin/ql-hba-snapshot --statistics <Host number/--all>
-proc, --procfs
This options forces the the utility to scans information based on "procfs", instead of default sysfs. Ex. # /usr/sbin/ql-hba-snap-
shot --procfs [Other valid option]
-v, --verbose
This enables verbose display. The detailed information of LUNs will be displayed in addition to standard one. This option is only
supported in sysfs. Ex. # /usr/sbin/ql-hba-snapshot --verbose <Host number/-a>
SEE ALSO
ql-dynamic-tgt-lun-disc(8), ql-lun-state-online(8), ql-set-cmd-timeout(8)
Matthias Schmitz <matthias@sigxcpu.org> July 2009 ql-hba-snapshot(8)