|
|
Sponsored Content
Operating Systems
Solaris
Ldom OS on SAN based zfs volume
Post 302347858 by bskin on Wednesday 26th of August 2009 05:27:22 PM
08-26-2009
|
|
10 More Discussions You Might Find Interesting
1. Linux
Dear Srs,
I have a Linux server (linux01) booting from SAN with a volume in a Nexsan SATAbeast storage array (san01). The disk/volume has four ext3 partitions, total size is near to 400GB, but only 20-30GB are in use.
I need to move this disk/volume to another Nexsan SATAbeast storage array... (0 Replies)
Discussion started by: Santi
0 Replies
2. Red Hat
Hi,
We have 200GB SAN volume mounted on Redhat EL 5. which is working fine. As my SAN supports dynamic resizing of volumes, i unmounted the volume and resized the SAN Volume to 300 GB successfully. Then i mounted again but it shows 200GB only but data is intact.
Now, my requirement is to let... (3 Replies)
Discussion started by: prvnrk
3 Replies
3. AIX
Hello all. I have a perplexing problem
I have an AIX 5.1 system on an EMC SAN.
This system had been on a CX400 SAN for several years. The system was migrated to a CX700 just over a week ago. The migration consisted of utilizing on of the HBAs in the system and connecting to both SANs
... (9 Replies)
Discussion started by: mhenryj
9 Replies
4. Solaris
Is there any way i can mount a zfs volume using snapshot or some other means ? (2 Replies)
Discussion started by: fugitive
2 Replies
5. Solaris
Hi, I need to expand a ZFS volume from 500GB to 800GB. I'd like to ask your help to confirm the following procedure:
Can I do it on the fly without bothering the users working on this volume?
Thank you in advance! (6 Replies)
Discussion started by: aixlover
6 Replies
6. Solaris
I have viewed a few previous posts regarding this, but none of them quite described or worked with my issue.
I am out of local disk space on my LDOM Manager but still have plenty of SAN vCPU and Memory available so I am trying to install a new LDOM OS on SAN.
I have exposed the SAN to the... (0 Replies)
Discussion started by: MobileGSP
0 Replies
7. Solaris
Apologies if this is the wrong forum..
I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
Discussion started by: tommyq
4 Replies
8. Red Hat
I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Discussion started by: rbatte1
4 Replies
9. Solaris
Hi all,
I'm using Solaris 11.3.
HBA port connected to SAN disk 3T.
AVAILABLE DISK SELECTIONS:
0. c0t600A0B800033696A0000214B571938F1d0 <SUN-CSM200_R-0760 cyl 44556 alt 2 hd 255 sec 189>
/scsi_vhci/ssd@g600a0b800033696a0000214b571938f1
1. c2t3C58620E0C565100d0... (1 Reply)
Discussion started by: manhte1
1 Replies
10. Solaris
Generally, this is what we do:-
On primary, export 2 LUNs (add-vdsdev).
On primary, assign these disks to the ldom in question (add-vdisk).
On ldom, created mirrored zpool from these two disks.
On one server (which is older) we have:-
On primary, create mirrored zpool from the two LUNs.... (4 Replies)
Discussion started by: psychocandy
4 Replies
LEARN ABOUT OPENSOLARIS
zdb
zdb(1M) System Administration Commands zdb(1M) NAME
zdb - ZFS debugger SYNOPSIS
zdb pool DESCRIPTION
The zdb command is used by support engineers to diagnose failures and gather statistics. Since the ZFS file system is always consistent on disk and is self-repairing, zdb should only be run under the direction by a support engineer. If no arguments are specified, zdb, performs basic consistency checks on the pool and associated datasets, and report any problems detected. Any options supported by this command are internal to Sun and subject to change at any time. EXIT STATUS
The following exit values are returned: 0 The pool is consistent. 1 An error was detected. 2 Invalid command line options were specified. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWzfsu | +-----------------------------+-----------------------------+ |Interface Stability |Unstable | +-----------------------------+-----------------------------+ SEE ALSO
zfs(1M), zpool(1M), attributes(5) SunOS 5.11 31 Oct 2005 zdb(1M)