08-25-2009
Check Have serial enable on system.
what O/p you are getting when trying hyper ( any junk character ?)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. Solaris
hello,
I have SunBlade 2000 with XVR-1000 graphics card. Xserver won't loaded. I've reinstalled OS 9 ( loaded Driver) nor 10 still won't do it. Anyone has this problem or have any ideas whats' wrong, greatly appreciated!!
thanks in adv. (1 Reply)
Discussion started by: anphdula
1 Replies
3. UNIX for Dummies Questions & Answers
platform: sunblade 100
Solaris 10.
When running a test-all from the ok prompt on this new (to me) system, it locks up at pci@1f,0/usb/c,3. It's been there for about 25 minutes.
I do have a usb keyboard and mouse attached, both are known good. There is no flash stick/ thumb drive... (0 Replies)
Discussion started by: montana77
0 Replies
4. Solaris
It's me again, I was taking my Sun Blade 100 apart last night to see what kind of drive I have. It is a Seagate ST320011A Barracuda ATA IV 20 GB 7200 RPM Ultra ATA/100 IDE.
Now 20 gig ain't all that big anymore and I got to thinking about putting a couple bigger drives in there. although I... (7 Replies)
Discussion started by: BrewDudeBob
7 Replies
5. Solaris
Hi, I've been a member for a while but have never posted. I have a Sun Blade 100 desktop and I just installed Solaris 10 and it is unbearably slow. I only have 128 Meg of RAM and need to upgrade. I have searched and found many online resources that have RAM, but I was wondering if anyone has... (12 Replies)
Discussion started by: BrewDudeBob
12 Replies
6. Solaris
Hi all,
I must connect my PC (Windows 2000) to Sun Enterprise 450 (4 X UltraSPARC-II 400Mhz) for Solaris 10 Installation. My PC doesn't have a serial port therefore I must use USB port.
How can I connect USB port of my PC to the serial port (DB 25) of Sun 450?
Will be there any problems with... (3 Replies)
Discussion started by: Sunb3
3 Replies
7. Solaris
FYI noob to here and sun blades...
I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly.
Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it... (2 Replies)
Discussion started by: shaun138
2 Replies
8. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
9. UNIX for Dummies Questions & Answers
For the past ten years I have owned a blade 100, and I had Solaris 9 running on it.
Due to the fact, 9 is woefully out of date, I wanted to try 10, but 10 needed more ram, so I beefed up the ram to the full 2 gig. I have two 15 gig ide drives in the box (stock drives). But unfortunately solaris... (2 Replies)
Discussion started by: RichardET
2 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I have server SUN BLADE T6340 and i tried install debian sparc on this machine.
Will it work ?
In the specification is written only Solaris 10. (4 Replies)
Discussion started by: PtaQ
4 Replies
LEARN ABOUT DEBIAN
sredird
sredird(8) sredird sredird(8)
NAME
sredird - RFC 2217 serial port server
SYNOPSIS
sredird [-i] log-level serial-device lock-file [poll-interval]
DESCRIPTION
This manual page documents briefly the sredird, program.
This program when run through inetd will use the RFC 2217 extensions to TELNET to implement serial commands over the TCP connection and
interface to a specified serial port.
OPTIONS
An optional first parameter is '-i' to enable compatability with Cisco IOS.
The first mandatory parameter is the log level for use in syslog. The next mandatory parameter is the device node for the serial device,
it must be a fully qualified path. The final mandatory parameter is the file name for the lock file to be used to prevent multiple
instances of sredird from talking to the serial port at the same time, or to allow sharing a port between modem and sredird.
EXAMPLE
Here is a configuration line for running it from inetd: sredir stream tcp nowait root /usr/sbin/tcpd /usr/sbin/sredird 5
/dev/modem /var/lock/LCK..modem
AUTHOR
This man page was written by Russell Coker <russell@coker.com.au>. May be freely used and distributed without restriction under the terms
of the GPL.
The sredird program was written by Denis Sbragion <d.sbragion@infotecna.it> and Jeffrey Altman <jaltman@columbia.edu>.
Russell Coker <russell@coker.com.au> 2.2.0 sredird(8)