08-25-2009
Check Have serial enable on system.
what O/p you are getting when trying hyper ( any junk character ?)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. Solaris
hello,
I have SunBlade 2000 with XVR-1000 graphics card. Xserver won't loaded. I've reinstalled OS 9 ( loaded Driver) nor 10 still won't do it. Anyone has this problem or have any ideas whats' wrong, greatly appreciated!!
thanks in adv. (1 Reply)
Discussion started by: anphdula
1 Replies
3. UNIX for Dummies Questions & Answers
platform: sunblade 100
Solaris 10.
When running a test-all from the ok prompt on this new (to me) system, it locks up at pci@1f,0/usb/c,3. It's been there for about 25 minutes.
I do have a usb keyboard and mouse attached, both are known good. There is no flash stick/ thumb drive... (0 Replies)
Discussion started by: montana77
0 Replies
4. Solaris
It's me again, I was taking my Sun Blade 100 apart last night to see what kind of drive I have. It is a Seagate ST320011A Barracuda ATA IV 20 GB 7200 RPM Ultra ATA/100 IDE.
Now 20 gig ain't all that big anymore and I got to thinking about putting a couple bigger drives in there. although I... (7 Replies)
Discussion started by: BrewDudeBob
7 Replies
5. Solaris
Hi, I've been a member for a while but have never posted. I have a Sun Blade 100 desktop and I just installed Solaris 10 and it is unbearably slow. I only have 128 Meg of RAM and need to upgrade. I have searched and found many online resources that have RAM, but I was wondering if anyone has... (12 Replies)
Discussion started by: BrewDudeBob
12 Replies
6. Solaris
Hi all,
I must connect my PC (Windows 2000) to Sun Enterprise 450 (4 X UltraSPARC-II 400Mhz) for Solaris 10 Installation. My PC doesn't have a serial port therefore I must use USB port.
How can I connect USB port of my PC to the serial port (DB 25) of Sun 450?
Will be there any problems with... (3 Replies)
Discussion started by: Sunb3
3 Replies
7. Solaris
FYI noob to here and sun blades...
I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly.
Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it... (2 Replies)
Discussion started by: shaun138
2 Replies
8. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
9. UNIX for Dummies Questions & Answers
For the past ten years I have owned a blade 100, and I had Solaris 9 running on it.
Due to the fact, 9 is woefully out of date, I wanted to try 10, but 10 needed more ram, so I beefed up the ram to the full 2 gig. I have two 15 gig ide drives in the box (stock drives). But unfortunately solaris... (2 Replies)
Discussion started by: RichardET
2 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I have server SUN BLADE T6340 and i tried install debian sparc on this machine.
Will it work ?
In the specification is written only Solaris 10. (4 Replies)
Discussion started by: PtaQ
4 Replies
LEARN ABOUT MOJAVE
jconsole
jconsole(1) General Commands Manual jconsole(1)
NAME
jconsole - J2SE Monitoring and Management Console
SYNOPSIS
jconsole [ options ] [ pid | [ host:port ... ] ]
PARAMETERS
pid Process ID of a Java VM that was started with -Dcom.sun.management.jmxremote option on the same machine. See JMX Monitoring
and Management for details at http://java.sun.com/j2se/1.5.0/docs/guide/management/agent.html.
host:port Host name on which the Java VM is running and the port number through which the Java VM's JMX Connector is published. See
JMX Monitoring and Management for details at http://java.sun.com/j2se/1.5.0/docs/guide/management/agent.html.
DESCRIPTION
The jconsole command launches a graphical console tool that enables you to monitor and manage Java applications and virtual machines on a
local or remote machine.
NOTE- This tool is experimental and may not be available in future versions of the JDK.
OPTIONS
-interval=n Set the update interval to n seconds (default is 4 seconds)
-notile Do not tile windows initially (for two or more connections)
-version Output version information abd exit.
-help Output help message and exit.
SEE ALSO
Monitoring and Management for Java Platform at http://java.sun.com/j2se/1.5.0/docs/guide/management/index.html
06 Feb 2004 jconsole(1)