08-22-2009
on the solaris machines have a look at the output of "dladm show-dev". also you can run test programs like "ttcp" to test your speed over the network...
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Sorry to keep bothering you guys like this with all these boring, related questions. But here's one that should be more readily answerable.
What command or file should i use to get the speed/data rate of a network link? This is the capacity speed for instance 10Mbps or 100 Mbps in the case of the... (2 Replies)
Discussion started by: mint1981
2 Replies
2. UNIX for Advanced & Expert Users
Hello, everyone:
i encounter a problem these days , pls help me ,thanks in advance.
my env:
machine: ES40 A ES40 B
os: true64 Unix 4.0f
note: src.tar 8M network card speed 100M
my problem:
... (3 Replies)
Discussion started by: q30
3 Replies
3. HP-UX
Hello,
can anyone tell me how to change network speed or duplex speed...don't understand the concept why that is imp when the server comes back up to check up on it.
Basically have to make sure that the setting from the orginial speed. (2 Replies)
Discussion started by: catwomen
2 Replies
4. Filesystems, Disks and Memory
Hello,
I have a Supermicro server with a P4SCI mother board running Debian Sarge 3.1. This is the "dmidecode" output related to RAM info:
RAM speed information is incomplete.. "Current Speed: Unknown", is there anyway/soft to get the speed of installed RAM modules? thanks!!
Regards :)... (0 Replies)
Discussion started by: Santi
0 Replies
5. IP Networking
Hi all, one of my Sun Box facing the problem.
The network port i had set to Auto-Negotiated and i had edited the /etc/system/ file in the Sun box as below:
set hme:hme_adv_autoneg_cap=1
set hme:hme_adv_100fdx_cap=0
set hme:hme_adv_100hdx_cap=0
But when i checked the /var/adm/messages/, it... (0 Replies)
Discussion started by: AirWalker83
0 Replies
6. Solaris
I recently learned that Sun Solaris network cards (ce devices) have problems with ndd -get commands. I did some searching and found out about the netstat -k command to show me the link speed. What is the best way to change the link speed (both one time and permanently)?
I am running Solaris 9... (7 Replies)
Discussion started by: hshapiro
7 Replies
7. Filesystems, Disks and Memory
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Discussion started by: W.C.C
1 Replies
8. UNIX for Dummies Questions & Answers
After installing PV (Para virtual drivers) drivers I m not able to check the network speed of my Ethernet port.
Please check the output of mii-tool and ethtool.
# mii-tool eth0
SIOCGMIIPHY on 'eth0' failed: Operation not supported
# ethtool eth0
Settings for eth0:
Link... (2 Replies)
Discussion started by: pinga123
2 Replies
9. Hardware
Dear all,
Would you know how to measure the max speed of a WIFI connection between a router and a laptop for instance?
Many thanks for your help!
Regards, (3 Replies)
Discussion started by: freddie50
3 Replies
10. Red Hat
Dear All,
I have an intel NUC running CentOS 7 and physically connected to my Netgear CBVG834G router.
They both have Gigabit Ethernet cards and supposedly a top notch network cable connecting the two devices.
But when I run ethtool the connection is only running at 100Mbit/s
What can I do... (3 Replies)
Discussion started by: freddie50
3 Replies
LEARN ABOUT CENTOS
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)