08-21-2009
Looking at the source code, if a NIC is set in low power mode, it will not autonegotiate 1000baseT.
Suggest you dump the NVRAM of this NIC and a "good" NIC and see if they are the same.
10 More Discussions You Might Find Interesting
1. HP-UX
Can anyone tell me how would I troubleshoot when /var becomes full with inodes? This is on HP11.11 system. Where used is 92%, ifree is 1891 iuse is 88%. Thanks. (3 Replies)
Discussion started by: catwomen
3 Replies
2. Shell Programming and Scripting
Hello,
Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node:
# rsh <name> "command"
I have to implement this script on all the clusters of my company (a lot of...).
Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies
3. HP-UX
Need help guys!
when running cmrunnode batch i'm getting this error
cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies
4. HP-UX
Hi,
Please advise me whereas I have two node cluster server configured with MC/SG. Application and DB are running on Node 1, while Node 2 is standby.
All the volume group devices are part of cluster environment. There is only one package running at node 1.
Node 2 is having the problem to... (1 Reply)
Discussion started by: rauphelhunter
1 Replies
5. High Performance Computing
hi,
i am trying to setup a 2 node cluster environment. following is what i have;
1. 2 x sun ultra60 - 450MHz procs, 1GB RAM, 9GB HDD, solaris 10
2. 2 x HBA cards
3. 2 x Connection leads to connect ultra60 with D1000
4. 1 x D1000 storage box.
5. 3 x 9GB HDD + 2 x 36GB HDD
first of all,... (1 Reply)
Discussion started by: solman17
1 Replies
6. Solaris
I now the logical name and Virtual IP of the cluster.
How can I find the active sun cluster node without having root access? (3 Replies)
Discussion started by: sreeniatbp
3 Replies
7. HP-UX
Hello,
Is there any way to identify the active node in a HP-UX cluster without root privileges? (3 Replies)
Discussion started by: psimoes79
3 Replies
8. Solaris
Hi Gurus,
I am very new to clustering and for test i have created a single node cluster, now i want to remove the system from cluster. Did some googling however as a newbee in cluster unable to co related the info.
Please help
Thanks (1 Reply)
Discussion started by: kumarmani
1 Replies
9. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
10. AIX
Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies
clinfo(1M) System Administration Commands clinfo(1M)
NAME
clinfo - display cluster information
SYNOPSIS
clinfo [-nh]
DESCRIPTION
The clinfo command displays cluster configuration information about the node from which the command is executed.
Without arguments, clinfo returns an exit status of 0 if the node is configured and booted as part of a cluster. Otherwise, clinfo returns
an exit status of 1.
OPTIONS
The following options are supported:
-h Displays the highest node number allowed to be configured. This is different from the maximum number of nodes supported in a given
cluster. The current highest configured node number can change immediately after the command returns since new nodes can be dynam-
ically added to a running cluster.
For example, clinfo -h might return 64, meaning that the highest number you can use to identify a node is 64. See the Sun Cluster
3.0 System Administration Guide for a description of utilities you can use to determine the number of nodes in a cluster.
-n Prints the number of the node from which clinfo is executed.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 An error occurred.
This is usually because the node is not configured or booted as part of a cluster.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
SunOS 5.10 12 Mar 2002 clinfo(1M)