Sponsored Content
Operating Systems AIX Link aggregation with hacmp ? Post 302346060 by zxmaus on Friday 21st of August 2009 01:35:31 AM
Old 08-21-2009
DukeNuke, Bakunin,

many thanks - I know our switches do support it ... we're running our vio servers with link aggregation - I just wanted to know if hacmp can cope with it, too. Since it is still presented as one adapter, I would think so ?

Rgds
zxmaus
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. IP Networking

bonding without switch link aggregation

I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies

4. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

5. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

6. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

7. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

8. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. Solaris

How can I test link aggregation?

Hi, I have Solaris-10 server and link aggregation is configured on this in below way # dladm show-aggr key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto) device address speed duplex link state bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
asadmin-delete-resource-adapter-config(1AS)			   User Commands		       asadmin-delete-resource-adapter-config(1AS)

NAME
asadmin-delete-resource-adapter-config, delete-resource-adapter-config - deletes the configuration information created in domain.xml for the connector module SYNOPSIS
delete-resource-adapter-config --user admin_user [--password admin_password][--host localhost] [--port 4848][--secure|-s] [--passwordfile filename] [--terse=false] [--echo=false] [--interactive=true] raname Deletes the entry in the resource-adapter-config element of the domain.xml file with the provided --raname. This command is supported in remote mode only. OPTIONS
--user authorized domain application server administrative username. --password password to administer the domain application server. --host machine name where the domain application server is running. --port port number of the domain application server listening for administration requests. --secure if true, uses SSL/TLS to communicate with the domain application server. --passwordfile file containing the domain application server password. --terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well- formatted data for consumption by a script. Default is false. --echo setting to true will echo the command line statement on the standard output. Default is false. --interactive if set to true (default), only the required password options are prompted. OPERANDS
raname the value kept in the resource-adapter-name in the domain.xml file. Example 1: Using delete-resource-adapter-config asadmin> delete-resource-adapter-config --username admin1 --password adminadmin myresourceadapter Command delete-resource-adapter-config executed successfully EXIT STATUS
0 command executed successfully 1 error in executing the command asadmin-create-resource-adapter-config(1AS), asadmin-list-resource-adapter-configs(1) J2EE 1.4 SDK March 2004 asadmin-delete-resource-adapter-config(1AS)
All times are GMT -4. The time now is 04:01 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy