|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Raid config on Jumpstart (Solaris 10
Post 302344690 by iman453 on Monday 17th of August 2009 10:09:02 AM
08-17-2009
Raid config on Jumpstart (Solaris 10
Hi there,
I was wondering if it is possible to include a RAID configuration in my Solaris 10 Jumpstart files, so that I don't have to manually set up RAID on all my machines.
Thanks
P.S. I started messing around with Solaris only a week back, so if I sound like a complete idiot, you know why
I was wondering if it is possible to include a RAID configuration in my Solaris 10 Jumpstart files, so that I don't have to manually set up RAID on all my machines.
Thanks
P.S. I started messing around with Solaris only a week back, so if I sound like a complete idiot, you know why
|
|
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I build a jumpstart server with a running dhcp server. I already managed to install a x86 client via network. But my sparc clients aren't still working.
When booting via network I get the following message:
Timeout waiting for ARP/RARP packet
I ran "snoop" on the server:
client2 ->... (1 Reply)
Discussion started by: Jay_Fisi
1 Replies
2. UNIX for Dummies Questions & Answers
How do you view Drive/RAID configuration in UNIX?
We are running an ML370 with 6 drives in it...
Version: Sco 5.2.0
Sco Openserver Release 5 (2 Replies)
Discussion started by: bpoulson
2 Replies
3. Solaris
I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Discussion started by: salty
5 Replies
4. Solaris
Hi all ,
I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows :
cleaning up preexisting install client "XXXXXXX"
removing XXXXXXXfrom bootparams
removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies
5. AIX
We have an IBM pseries with AIX 5.1 that we are going to set up with RAID 5. It has a 7028-2498 RAID controller that was never configured, long story. It has six 36GB drives, and my question is, can we set up the RAID 5 array before reloading AIX, such that all six drives are part of the array? (6 Replies)
Discussion started by: markper
6 Replies
6. Solaris
I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt
after running a boot net - install
Link hasn't comeup yet
Ran a test-net and got the following message.
Link is -- down
When... (7 Replies)
Discussion started by: soupbone38
7 Replies
7. Solaris
Hello everyone,
I tried to install solaris 10 using the command # boot net - install.
I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following:
... (7 Replies)
Discussion started by: yflores
7 Replies
8. Solaris
I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems.
Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86?
Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies
9. Solaris
Hello,
Can anyone share a good online article/tutorial on how to properly set up JumpStart server for Solaris 10?
Thanks,
Regards. (3 Replies)
Discussion started by: NewSolarisSquad
3 Replies
LEARN ABOUT LINUX
iir
IIR(4) BSD Kernel Interfaces Manual IIR(4) NAME
iir -- Intel Integrated RAID controller and ICP Vortex driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device pci device scbus device iir Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): iir_load="YES" DESCRIPTION
The iir driver claims to interface with the Intel integrated RAID controller cards, and all versions of the ICP Vortex controllers (including FC). HARDWARE
Controllers supported by the iir driver include: o Intel RAID Controller SRCMR o Intel Server RAID Controller U3-l (SRCU31a) o Intel Server RAID Controller U3-1L (SRCU31La) o Intel Server RAID Controller U3-2 (SRCU32) o All past and future releases of Intel and ICP RAID Controllers. o Intel RAID Controller SRCU21 (discontinued) o Intel RAID Controller SRCU31 (older revision, not compatible) o Intel RAID Controller SRCU31L (older revision, not compatible) The SRCU31 and SRCU31L can be updated via a firmware update available from Intel. SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8) AUTHORS
The iir driver is supported and maintained by Achim Leubner <Achim_Leubner@adaptec.com>. This manual page was written by Tom Rhodes <trhodes@FreeBSD.org> and is based on information supplied by the driver authors and the website of Mike Smith <msmith@FreeBSD.org>. BSD August 8, 2004 BSD