How to active this network adapter? Post: 302344312

10 More Discussions You Might Find Interesting

1. Solaris

Sun v440/v880 network adapter teaming

Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so?

2. AIX

hacmp network adapter re-define

I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not...

3. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec

4. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the...

5. IP Networking

Maximum IP Address Configured on Intel Network Adapter

Hi All, Sorry if this is not the correct forum to answer. But hope somebody can help me... For these two types of network adapter: Intel(R) PRO/1000 MT Server Adapter Intel(R) PRO/1000 MT Dual Port Network Adapter How many IP addresses can be configured on it at the same time? System...

6. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network...

7. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network...

8. Programming

Compiling virtual network adapter driver problem (net_device struct)

Hi, I found on linuxgazette.net/93/bhaskaran.html page very useful sample of virtual driver (not connected to real hardware). I try to compile it with no effect. So: I got fresh Ubuntu 9.10 (kernel 2.6.31-14) My source is saved in networkAdapter.c file in /usr/src/myModules directory. I...

9. Hardware

Problematic RTL8188EE Wireless Network Adapter

Good Day All, There are numerous results when searching google on this issue, however, none seem to have a solution. I have read until my eyes bleed and banged my head on the table more than once! :) I am hoping to resolve this issue -- or at least have a decent workaround. It is a real...

10. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver...

LEARN ABOUT DEBIAN

guards

GUARDS(1)						User Contributed Perl Documentation						 GUARDS(1)

NAME

       guards - select from a list of files guarded by conditions

SYNOPSIS

       guards [--prefix=dir] [--path=dir2:dir2:...] [--default=0|1]	   [-v|--invert-match] [--list|--check] [--config=file]        symbol ...

DESCRIPTION

       The script reads a configuration file that may contain so-called guards, file names, and comments, and writes those file names that satisfy
       all guards to standard output. The script takes a list of symbols as its arguments. Each line in the configuration file is processed
       separately. Lines may start with a number of guards. The following guards are defined:

	   +xxx Include the file(s) on this line if the symbol xxx is defined.

	   -xxx Exclude the file(s) on this line if the symbol xxx is defined.

	   +!xxx Include the file(s) on this line if the symbol xxx is not defined.

	   -!xxx Exclude the file(s) on this line if the symbol xxx is not defined.

	   - Exclude this file. Used to avoid spurious --check messages.

       The guards are processed left to right. The last guard that matches determines if the file is included. If no guard is specified, the
       --default setting determines if the file is included.

       If no configuration file is specified, the script reads from standard input.

       The --check option is used to compare the specification file against the file system. If files are referenced in the specification that do
       not exist, or if files are not enlisted in the specification file warnings are printed. The --path option can be used to specify which
       directory or directories to scan.  Multiple directories are separated by a colon (":") character. The --prefix option specifies the
       location of the files.

AUTHOR

       Andreas Gruenbacher <agruen@suse.de> (SuSE Linux AG)

perl v5.14.2							    2012-03-04								 GUARDS(1)