08-14-2009
If you are using emulex adapters, the lputil utility provided with their package will add entries to your configuration files for you.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
I want a help for Configuring snmpd.conf and snmptrapd.conf (i.e Configuring SNMP)
for receiving
TRAPS in my networks. I am using RHEL4.0 OS.
Please tell me How I can configure above two files in a proper way and at an
advanced level.
Especially I am getting... (2 Replies)
Discussion started by: jagdish.machhi@
2 Replies
2. UNIX for Dummies Questions & Answers
Folks;
I know this might sounds stupid, but please help with this:
I have share in my smb.conf on my SUSE 10 box.
How can i make this share accessible to outside IP range or a specific IP address without need for user/pass?
Here's the share as it's written in smb.conf:
;
;comment =... (0 Replies)
Discussion started by: Katkota
0 Replies
3. Solaris
Hey all!
I'm working on Solaris10 right now and I was fiddling around with a fresh install and was wondering about the service that uses resolv.conf?
I know prior to Sol10 (SMF) it was /etc/init.d/inetsvc stop and start to reload resolv.conf changes
but I can't seem to find the correct SMF... (5 Replies)
Discussion started by: Keepcase
5 Replies
4. Solaris
OK I am running solaris 10.
I made some changes to my ipf.conf file and issued the command:
ipf -Fa -f /etc/ipf/ipf.conf
to flush out the old and bring in the new changes.
When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see.
I... (3 Replies)
Discussion started by: NewSolarisAdmin
3 Replies
5. Red Hat
What would be Redhat RHEL 4.0 equivalent for Solaris sd.conf and lpfc.conf? What are the files called and where are the files located? (1 Reply)
Discussion started by: soupbone38
1 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I have a question on /etc/syslog.conf file in Solaris 10.
Below is a line taken from /etc/syslog.conf file and I know that the last field (operator) is where the logs gets outputted but how do I find out what the output file name format is going to be and which directory it gets outputted... (1 Reply)
Discussion started by: stevefox
1 Replies
7. UNIX for Advanced & Expert Users
i have this program running on my solaris and there are two identical config files, i am not sure which one is being used by this program but I am sure it uses one of them.
I run lsof -p {pid} but it does not show which config file has been read by this program, what i am doing wrong?
thanks (4 Replies)
Discussion started by: fedora
4 Replies
8. Red Hat
Hi,
I was told to add the "nis" in front of "files" for below lines in /etc/nsswitch.conf was not in a good practise. I tried to search in google and man page for nsswitch.conf and can't find the answer. could someone please help me?
passwd: nis files
shadow: nis files
group: nis files... (2 Replies)
Discussion started by: beeloo
2 Replies
9. Shell Programming and Scripting
Hello all,
Newbie here.
I'm currently tasked with updating rsyslog.conf and auditd.conf on a large set of servers. I know the exact logging configurations that I want to enable. I have updated both files on on a server and hope to use the updated files as a template for the rest of the... (3 Replies)
Discussion started by: Mide
3 Replies
10. Solaris
Hi,
I've installed Solaris 11.3(live media) and configured DNS. Everytime I reboot the server, resolv.conf got deleted and it created a new nsswitch.conf.
I used below to configure both settings:
# svccfg -s dns/client
svc:/network/dns/client> setprop config/nameserver = (xx.xx.xx.aa... (1 Reply)
Discussion started by: flexihopper18
1 Replies
LEARN ABOUT CENTOS
iprupdate
IPRUPDATE(8) System Manager's Manual IPRUPDATE(8)
NAME
iprupdate - IBM Power RAID adapter/device microcode update utility
SYNOPSIS
iprupdate
iprupdate --debug --check_only --daemon --use-polling --use-uevents
DESCRIPTION
iprupdate is used to update the microcode on IBM storage adapters and the disk units attached to them to a minimum supported level. It can
be run at any time while the ipr device driver is loaded. The utility will check the microcode revision level of each storage adapter/disk
unit on the system and compare it to the microcode revision level that is installed in /etc/microcode, /usr/lib/microcode, and
/lib/firmware. If the microcode level on the adapter/device is below the minimum supported level and the level of the latest image is
newer, the microcode will be updated to the latest level available. It is desired that this be called in the boot process.
OPTIONS
--version
Print the version number of iprupdate
--debug
Enable additional error logging. Enabling this will result in additional errors logging to /var/log/messages.
--check_only
Check if any adapters or disk units are below their minimum supported level.
--daemon
Run as a daemon to handle adapters and devices being hotplugged.
--use-polling
Do not use netlink/uevent notification, but rather poll for adapter and device configuration changes.
--use-uevents
Use netlink/uevent notification rather than polling for adapter and device configuration changes. If not specified, polling will be
used until the first uevent notification appears, then netlink will be used.
AUTHOR
Brian King (brking@us.ibm.com)
February 2005 IPRUPDATE(8)