08-14-2009
What type of "tool" you're referring to?
CAM software?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
I want a help for Configuring snmpd.conf and snmptrapd.conf (i.e Configuring SNMP)
for receiving
TRAPS in my networks. I am using RHEL4.0 OS.
Please tell me How I can configure above two files in a proper way and at an
advanced level.
Especially I am getting... (2 Replies)
Discussion started by: jagdish.machhi@
2 Replies
2. UNIX for Dummies Questions & Answers
Folks;
I know this might sounds stupid, but please help with this:
I have share in my smb.conf on my SUSE 10 box.
How can i make this share accessible to outside IP range or a specific IP address without need for user/pass?
Here's the share as it's written in smb.conf:
;
;comment =... (0 Replies)
Discussion started by: Katkota
0 Replies
3. Solaris
Hey all!
I'm working on Solaris10 right now and I was fiddling around with a fresh install and was wondering about the service that uses resolv.conf?
I know prior to Sol10 (SMF) it was /etc/init.d/inetsvc stop and start to reload resolv.conf changes
but I can't seem to find the correct SMF... (5 Replies)
Discussion started by: Keepcase
5 Replies
4. Solaris
OK I am running solaris 10.
I made some changes to my ipf.conf file and issued the command:
ipf -Fa -f /etc/ipf/ipf.conf
to flush out the old and bring in the new changes.
When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see.
I... (3 Replies)
Discussion started by: NewSolarisAdmin
3 Replies
5. Red Hat
What would be Redhat RHEL 4.0 equivalent for Solaris sd.conf and lpfc.conf? What are the files called and where are the files located? (1 Reply)
Discussion started by: soupbone38
1 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I have a question on /etc/syslog.conf file in Solaris 10.
Below is a line taken from /etc/syslog.conf file and I know that the last field (operator) is where the logs gets outputted but how do I find out what the output file name format is going to be and which directory it gets outputted... (1 Reply)
Discussion started by: stevefox
1 Replies
7. UNIX for Advanced & Expert Users
i have this program running on my solaris and there are two identical config files, i am not sure which one is being used by this program but I am sure it uses one of them.
I run lsof -p {pid} but it does not show which config file has been read by this program, what i am doing wrong?
thanks (4 Replies)
Discussion started by: fedora
4 Replies
8. Red Hat
Hi,
I was told to add the "nis" in front of "files" for below lines in /etc/nsswitch.conf was not in a good practise. I tried to search in google and man page for nsswitch.conf and can't find the answer. could someone please help me?
passwd: nis files
shadow: nis files
group: nis files... (2 Replies)
Discussion started by: beeloo
2 Replies
9. Shell Programming and Scripting
Hello all,
Newbie here.
I'm currently tasked with updating rsyslog.conf and auditd.conf on a large set of servers. I know the exact logging configurations that I want to enable. I have updated both files on on a server and hope to use the updated files as a template for the rest of the... (3 Replies)
Discussion started by: Mide
3 Replies
10. Solaris
Hi,
I've installed Solaris 11.3(live media) and configured DNS. Everytime I reboot the server, resolv.conf got deleted and it created a new nsswitch.conf.
I used below to configure both settings:
# svccfg -s dns/client
svc:/network/dns/client> setprop config/nameserver = (xx.xx.xx.aa... (1 Reply)
Discussion started by: flexihopper18
1 Replies
XPT(4) BSD Kernel Interfaces Manual XPT(4)
NAME
xpt -- CAM transport layer interface
SYNOPSIS
None.
DESCRIPTION
The xpt driver provides a way for userland applications to issue certain CAM CCBs to the kernel.
Since the xpt driver allows direct access to the CAM subsystem, system administrators should exercise caution when granting access to this
driver. If used improperly, this driver can allow userland applications to crash a machine or cause data loss.
KERNEL CONFIGURATION
There is no kernel configuration required for the xpt driver. It is enabled when SCSI support is enabled in the kernel. There is one
instance of the xpt driver per CAM transport layer instance. Since there is currently only one CAM transport layer, there will only be one
instance of this driver.
IOCTLS
CAMIOCOMMAND This ioctl takes certain kinds of CAM CCBs and passes them through to the CAM transport layer for action. Only the following
CCB types are supported:
XPT_SCAN_BUS
XPT_RESET_BUS
XPT_SCAN_LUN
XPT_ENG_INQ
XPT_ENG_EXEC
XPT_DEBUG
XPT_DEV_MATCH
XPT_PATH_INQ
The above CCBs are the only ones supported since it makes more sense to send them through a generic passthrough device rather
than a passthrough device tied to a particular underlying SCSI device.
CAMGETPASSTHRU This ioctl takes an XPT_GDEVLIST CCB, and returns the passthrough device corresponding to the device in question.
FILES
/dev/xpt0 Character device node for the xpt driver.
DIAGNOSTICS
None.
SEE ALSO
cam(3), cam_cdbparse(3), pass(4), camcontrol(8)
HISTORY
The CAM transport layer driver first appeared in FreeBSD 3.0.
AUTHORS
Kenneth Merry <ken@FreeBSD.org>
BSD
October 10, 1998 BSD