Sponsored Content
Operating Systems AIX changing Physical Partition (PP) Post 302344005 by eRJe on Friday 14th of August 2009 10:22:09 AM
Old 08-14-2009
changing Physical Partition (PP)

Hi all,

I am trying to replace an old 9gb hard disk for a 36gb hard drive on an AIX 4.3.2 system (can't update)

I was thinking of doing this by doing a dd from the 9gb to the 36gb hard drive and then resize the Logical Volumes. However, lspv <36gb hard disk> gives me the folowing:

Code:
#lrnt> lspv hdisk6
PHYSICAL VOLUME:    hdisk0                   VOLUME GROUP:     rootvg
PV IDENTIFIER:      0035570279651069         VG IDENTIFIER     00355702e19f34a0
PV STATE:           active                                     
STALE PARTITIONS:   0                        ALLOCATABLE:      yes
PP SIZE:            16 megabyte(s)           LOGICAL VOLUMES:  9
TOTAL PPs:          542 (8672 megabytes)     VG DESCRIPTORS:   2
FREE PPs:           29 (464 megabytes)                         
USED PPs:           513 (8208 megabytes)                       
FREE DISTRIBUTION:  00..00..00..00..29                         
USED DISTRIBUTION:  109..108..108..108..80        

I can only allocate an extra 29 PPs = 464mb. Where are the rest of the PPs of how can I increase the PP size?

Or should I be using a different way to upgrade the (boot)disk?


Thanks,
Robbert
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

vol group - physical partition size

Hi Everyone, Can someone tell me the effect of the pp size of the volume group created for Oracle data. It would seem that creating small pp's will cause more overhead. What if you make the pp to large? What should I base this size on? Thanks, (4 Replies)
Discussion started by: kburrows
4 Replies

2. UNIX for Dummies Questions & Answers

understanding logical partition, physical partition

hi, 1) is logical partition the same as physical partition except that one is physical and the other is logical? 2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies

3. UNIX for Dummies Questions & Answers

physical volume and physical disk.

Hello, I need explanations about physical disks and physical volumes. What is the difference between these 2 things? In fact, i am trying to understand what the AIX lspv2command does. Thank you in advance. (2 Replies)
Discussion started by: VeroL
2 Replies

4. UNIX for Dummies Questions & Answers

Physical volume- no free physical partitions

I was in smit, checking on disc space, etc. and it appears that one of our physical volumes that is part of a large volume group, has no free physical partitions. The server is running AIX 5.1. What would be the advisable step to take in this instance? (9 Replies)
Discussion started by: markper
9 Replies

5. AIX

Maximum Limit of HMC to handle Physical Power Virtualization Physical Machine

Hello All, Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time? Thanks, Jenish (1 Reply)
Discussion started by: jenish_shah
1 Replies

6. UNIX for Dummies Questions & Answers

Confusion Regarding Physical Volume,Volume Group,Logical Volume,Physical partition

Hi, I am new to unix. I am working on Red Hat Linux and side by side on AIX also. After reading the concepts of Storage, I am now really confused regarding the terminologies 1)Physical Volume 2)Volume Group 3)Logical Volume 4)Physical Partition Please help me to understand these concepts. (6 Replies)
Discussion started by: kashifsd17
6 Replies

7. Solaris

Partition overlaps another partition while creating new parition in solaris

hi all while formatting hard disk i am getting following error. Partition 1 ends at 266338338 It must be between 34 and 143374704. label error: EFI Labels do not support overlapping partitions Partition 8 overlaps partition 1. Warning: error writing EFI. Label failed. I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies

8. Red Hat

Shrink LVM partition & create new Linux Primary partition

Hello All, I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows, /boot - Linux Partition & another is LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc). Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies

9. Solaris

Changing physical block size in ssd.conf Solaris

Close (0 Replies)
Discussion started by: gull05
0 Replies
hdio(7I)                                                          Ioctl Requests                                                          hdio(7I)

NAME
hdio - SMD and IPI disk control operations SYNOPSIS
#include <sys/hdio.h> DESCRIPTION
Note - The SMC and IPI drivers have been discontinued. dkio(7I) is now the preferred method for retrieving disk information. The SMD and IPI disk drivers supplied with this release support a set of ioctl(2) requests for diagnostics and bad sector information. Basic to these ioctl() requests are the definitions in <sys/hdio.h>. IOCTLS
HDKIOCGTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() gets specific information from the hard disk. HDKIOCSTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() sets specific information about the hard disk. /* * Used for drive info */ struct hdk_type { ushort_t hdkt_hsect; /* hard sector count (read only) */ ushort_t hdkt_promrev; /* prom revision (read only) */ uchar_t hdkt_drtype; /* drive type (ctlr specific) */ uchar_t hdkt_drstat; /* drive status (ctlr specific, ro) */ }; HDKIOCGBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to get the bad sector map from the disk. HDKIOCSBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to set the bad sector map on the disk. /* * Used for bad sector map */ struct hdk_badmap { caddr_t hdkb_bufaddr; /* address of user's map buffer */ }; HDKIOCGDIAG The argument is a pointer to a hdk_diag structure (described below). This ioctl() gets the most recent command that failed along with the sector and error number from the hard disk. /* * Used for disk diagnostics */ struct hdk_diag { ushort_t hdkd_errcmd; /* most recent command in error */ daddr_t hdkd_errsect; /* most recent sector in error */ uchar_t hdkd_errno; /* most recent error number */ uchar_t hdkd_severe; /* severity of most recent error */ }; SEE ALSO
ioctl(2), dkio(7I) SunOS 5.10 13 Aug 2002 hdio(7I)
All times are GMT -4. The time now is 01:50 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy