08-14-2009
You need to move the data from /opt/opennms/share/rrd to the storage/onms/rrd filesystem.
10 More Discussions You Might Find Interesting
1. Solaris
Hi all
I plan to install Solaris 10U6 on some SPARC server using ZFS as root pool, whereas I would like to keep the current setup done by VxVM:
- 2 internal disks: c0t0d0 and c0t1d0
- bootable root-volume (mirrored, both disks)
- 1 non-mirrored swap slice
- 1 non-mirrored slices for Live... (1 Reply)
Discussion started by: blicki
1 Replies
2. Solaris
I created a pool the other day. I created a 10 gig files just for a test, then deleted it.
I proceeded to create a few files systems. But for some reason the pool shows 10% full, but the files systems are both at 1%? Both files systems share the same pool.
When I ls -al the pool I just... (6 Replies)
Discussion started by: mrlayance
6 Replies
3. Solaris
Hi guys,
We had created a pool as follows:
zpool create filing_pool raidz c1t2d0 c1t3d0 ........
Due to some requirement, we need to destroy the pool and re-create another one. We wish to know now which disks have been included in the filing_pool, how do we list the disks used to create... (2 Replies)
Discussion started by: frum
2 Replies
4. Solaris
I need to migrate an existing raidz pool to a new raidz pool with larger disks. I need the mount points and attributes to migrate as well. What is the best procedure to accomplish this. The current pool is 6x36GB disks 202GB capacity and I am migrating to 5x 72GB disks 340GB capacity. (2 Replies)
Discussion started by: jac
2 Replies
5. Solaris
Other than export/import, is there a cleaner way to rename a pool without unmounting de FS?
Something like, say "zpool rename a b"?
Thanks. (2 Replies)
Discussion started by: verdepollo
2 Replies
6. Solaris
installed Solaris 11 Express on my server machine a while ago. I created a Z2 RAID over five HDDs and created a few ZFS filesystems on it.
Once I (unintentionally) managed to fill the pool completely with data and (to my surprise) the filesystems stopped working - I could not read/delete any... (3 Replies)
Discussion started by: RychnD
3 Replies
7. Solaris
I have a branded zone txdjintra that utilizes a pool named Pool_djintra that is no longer required. There is a 150 Gig Lun assigned to the pool that I need to reassign to another branded zone txpsrsrv07 with a pool named Pool_txpsrsrv07 on the same sun blade. What is the process to do this?
... (0 Replies)
Discussion started by: jeffsr
0 Replies
8. Solaris
I accidently added a disk in different zpool instead of pool, where I want.
root@prtdrd21:/# zpool status cvfdb2_app_pool
pool: cvfdb2_app_pool
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
cvfdb2_app_pool ONLINE 0 0 0... (1 Reply)
Discussion started by: solaris_1977
1 Replies
9. Solaris
I have a newly created zpool, and I have set compression on, for the whole pool:
# zfs set compression=on newPool
Now I have zfs send | zfs receive lot of snapshots to my newPool, but the compression is gone. I was hoping that I would be able to send snapshots to the new pool (which is... (0 Replies)
Discussion started by: kebabbert
0 Replies
10. UNIX for Beginners Questions & Answers
I have installed FreeBSD onto a raw image file using QEMU Emulator successfully. I have formatted the image file using the ZFS file system (ZFS POOL).
Using the following commands below I have successfully mounted the image file ready to be opened by zpool
sudo losetup /dev/loop0 .img sudo... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT DEBIAN
add_txrx
ADD_TXRX(1) General Commands Manual ADD_TXRX(1)
NAME
add_txrx - add two new Data Sources called 'tx' and 'rx' to an RRD file
SYNOPSIS
add_txrx <file> ...
DESCRIPTION
This utility is used when upgrading from FlowScan-1.005 (or less) to FlowScan-1.006 (or greater). It is used to add two new Data Sources
to FlowScan ".rrd" files. e.g.:
$ make install # install FlowScan-1.006 in your existing FlowScan dir
$ cd $prefix/graphs
$ add_txrx total.rrd *.*.*.*_*.rrd
tx - a count of the unique source IP addresses
that have transmitted flows
rx - a count of the unique destination IP addresses
that have received flows
These Data Sources will allows FlowScan users to calculate the average number of bytes, packets, and flows per host and to determine the
overall level of activity (in terms of numbers of individual hosts) for each subnet and for the entire campus.
The values will be recorded only if you use the TopN directive with the CampusIO and/or SubNetIO reports. TopN was introduced in FlowS-
can-1.006.
For instance, if you set CampusIO's TopN to a value greater than zero, the tx value in FlowScan's "total.rrd" is the number of unique
source IP addresses (hosts) from which FlowScan has seen outbound flows.
Upgrading your RRD Files
If you are upgrading, it is necessary to add two new Data Sources to the some of your existing RRD files. Before running flowscan, backup
your RRD files, e.g.:
$ cd $prefix/graphs
$ tar cf saved_rrd_files.tar *.rrd
then do this:
$ cd $prefix/graphs
$ ../bin/add_txrx total.rrd [1-9]*.*.*.*_*.rrd
SEE ALSO
add_ds.pl(1), event2vrule(1), flowscan(1), ip2hostname(1), locker(1)
AUTHOR
This manual page was written by Anibal Monsalve Salazar, for the Debian Project.
ADD_TXRX(1)