Ok but the problem is the last domain wich i created domain 02 has the 2 fiber cards and the second domain domain 01 has all the NICS on board and external one. There's another thing after the XSB was set in quad mode the 2 domains are showing 16g of memory for each XSB isn't there anyway to assign it to one of the domain
Hi,
I 've a fully loaded M5000 which i would like to partition in 4 domains but i have a concern that since we have only 4 internal disks how can we partition the box in for domains with 2 disks ( mirrored ) in each domain. Should i go ahead with 1 Lun from SAN and 1 internal disk for each of 4... (3 Replies)
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Hi
We have an M5000 with one domain running Sun Cluster on it. We would like to split the domain into two domains. One with the existing Sun Cluster and one with a fresh install. We have 2 CPU Boards (8 CPU) / 4 Mem Boards (64 gb memory) and 2 IOU as well as 4 disks
Is it possible to have... (9 Replies)
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Hi Forum
please help me to fix M5000 Server which we were not using. now i logged to serve and foung that everything is showing as Deconfigured.
XSCF> showhardconf
SPARC Enterprise M5000;
+ Serial:BDF1051F30; Operator_Panel_Switch:Locked;
+ Power_Supply_System:Single;... (4 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
on an m5000 , I can not power it up, system failure.
XSCF> poweron -a
DomainIDs to power on:00,01
Continue? :y
00 :Not powering on :Poweron canceled due to missing component.
01 :Not powering on :Poweron canceled due to missing component.
the only fault that I can see is:
... (4 Replies)
Discussion started by: goya
4 Replies
LEARN ABOUT DEBIAN
graphics::primitive::insets
Graphics::Primitive::Insets(3pm) User Contributed Perl Documentation Graphics::Primitive::Insets(3pm)NAME
Graphics::Primitive::Insets - Space between things
DESCRIPTION
Graphics::Primitive::Insets represents the amount of space that surrounds something. This object can be used to represent either padding
or margins (in the CSS sense, one being inside the bounding box, the other being outside)
SYNOPSIS
use Graphics::Primitive::Insets;
my $insets = Graphics::Primitive::Insets->new({
top => 5,
bottom => 5,
left => 5,
right => 5
});
METHODS
Constructor
new Creates a new Graphics::Primitive::Insets.
Instance Methods
as_array
Return these insets as an array in the form of top, right, bottom and left.
bottom
Set/Get the inset from the bottom.
equal_to
Determine if these Insets are equal to another.
left
Set/Get the inset from the left.
right
Set/Get the inset from the right.
top Set/Get the inset from the top.
zero
Sets all the insets (top, left, bottom, right) to 0.
AUTHOR
Cory Watson, "<gphat@cpan.org>"
SEE ALSO perl(1)COPYRIGHT & LICENSE
Copyright 2008-2010 by Cory G Watson.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.12.3 2010-08-21 Graphics::Primitive::Insets(3pm)