Now i want to partition the 2nd domain further to create a 3rd domain with equal resources on both 2nd and 3rd. For that i set the XSB to quad mode and created the 3rd domin. But now the 3rd domain does not have any network interface and no HDD and the 2nd domain has been deprived of HBA cards. Is it possible to move one HBA card from 3rd to second domain and one network interface from 2nd to 3rd domain ?
Let me know if i some needs more info on this.
Code:
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00) Assigned y y y Passed Normal
01-0 01(01) Assigned y y y Passed Normal
01-1 02(00) Assigned y n n Passed Normal
01-2 SP Unavailable y n n Unmount Normal
01-3 SP Unavailable y n n Unmount Normal
XSCF>
Hi,
I 've a fully loaded M5000 which i would like to partition in 4 domains but i have a concern that since we have only 4 internal disks how can we partition the box in for domains with 2 disks ( mirrored ) in each domain. Should i go ahead with 1 Lun from SAN and 1 internal disk for each of 4... (3 Replies)
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Hi
We have an M5000 with one domain running Sun Cluster on it. We would like to split the domain into two domains. One with the existing Sun Cluster and one with a fresh install. We have 2 CPU Boards (8 CPU) / 4 Mem Boards (64 gb memory) and 2 IOU as well as 4 disks
Is it possible to have... (9 Replies)
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Hi Forum
please help me to fix M5000 Server which we were not using. now i logged to serve and foung that everything is showing as Deconfigured.
XSCF> showhardconf
SPARC Enterprise M5000;
+ Serial:BDF1051F30; Operator_Panel_Switch:Locked;
+ Power_Supply_System:Single;... (4 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
on an m5000 , I can not power it up, system failure.
XSCF> poweron -a
DomainIDs to power on:00,01
Continue? :y
00 :Not powering on :Poweron canceled due to missing component.
01 :Not powering on :Poweron canceled due to missing component.
the only fault that I can see is:
... (4 Replies)
Discussion started by: goya
4 Replies
LEARN ABOUT SUNOS
asadmin-stop-domain
asadmin-stop-domain(1AS) User Commands asadmin-stop-domain(1AS)NAME
asadmin-stop-domain, stop-domain - stops the given domain
SYNOPSIS
stop-domain [--domaindir install_dir/domains][--terse=false] [--echo=false] [domain_name]
stop-domain stops the specified domain. If there is only one domain in the default domain directory (install_dir/domains), then no operand
is required to stop the domain. However, if there is more than one domain, the domain operand must be specified. This command is supported
in local mode only.
OPTIONS --domaindir directory where the domain is to be stopped. If specified, path must be accessible in the filesystem. If not speci-
fied, the domainis stopped in the default install_dir/domains directory.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
OPERANDS
domain_name name of the domain. Must be a unique name.
Example 1: Using stop-domain
asadmin> stop-domain sampleDomain
Stoping Domain sampleDomain, please wait
Domain sampleDomain stopped
Command stop-domain executed successfully
Where: the sampleDomain domain in the default domains directory is stopped.
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-domain(1AS), asadmin-delete-domain(1AS), asadmin-start-domain(1AS), asadmin-list-domains(1AS)J2EE 1.4 SDK March 2004 asadmin-stop-domain(1AS)