You absolutely need to edit this file for SAN devices unless you have a tool that does it for you. Solaris will not search for LUN's that are not listed in this file.
The following will search the first 4 SAN devices it finds for LUN ID's 0, 1 and 2:
HI,
I want a help for Configuring snmpd.conf and snmptrapd.conf (i.e Configuring SNMP)
for receiving
TRAPS in my networks. I am using RHEL4.0 OS.
Please tell me How I can configure above two files in a proper way and at an
advanced level.
Especially I am getting... (2 Replies)
Folks;
I know this might sounds stupid, but please help with this:
I have share in my smb.conf on my SUSE 10 box.
How can i make this share accessible to outside IP range or a specific IP address without need for user/pass?
Here's the share as it's written in smb.conf:
;
;comment =... (0 Replies)
Hey all!
I'm working on Solaris10 right now and I was fiddling around with a fresh install and was wondering about the service that uses resolv.conf?
I know prior to Sol10 (SMF) it was /etc/init.d/inetsvc stop and start to reload resolv.conf changes
but I can't seem to find the correct SMF... (5 Replies)
OK I am running solaris 10.
I made some changes to my ipf.conf file and issued the command:
ipf -Fa -f /etc/ipf/ipf.conf
to flush out the old and bring in the new changes.
When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see.
I... (3 Replies)
Hi,
I have a question on /etc/syslog.conf file in Solaris 10.
Below is a line taken from /etc/syslog.conf file and I know that the last field (operator) is where the logs gets outputted but how do I find out what the output file name format is going to be and which directory it gets outputted... (1 Reply)
i have this program running on my solaris and there are two identical config files, i am not sure which one is being used by this program but I am sure it uses one of them.
I run lsof -p {pid} but it does not show which config file has been read by this program, what i am doing wrong?
thanks (4 Replies)
Hi,
I was told to add the "nis" in front of "files" for below lines in /etc/nsswitch.conf was not in a good practise. I tried to search in google and man page for nsswitch.conf and can't find the answer. could someone please help me?
passwd: nis files
shadow: nis files
group: nis files... (2 Replies)
Hello all,
Newbie here.
I'm currently tasked with updating rsyslog.conf and auditd.conf on a large set of servers. I know the exact logging configurations that I want to enable. I have updated both files on on a server and hope to use the updated files as a template for the rest of the... (3 Replies)
Hi,
I've installed Solaris 11.3(live media) and configured DNS. Everytime I reboot the server, resolv.conf got deleted and it created a new nsswitch.conf.
I used below to configure both settings:
# svccfg -s dns/client
svc:/network/dns/client> setprop config/nameserver = (xx.xx.xx.aa... (1 Reply)
Discussion started by: flexihopper18
1 Replies
LEARN ABOUT SUSE
tran_reset
tran_reset(9E) Driver Entry Points tran_reset(9E)NAME
tran_reset - reset a SCSI bus or target
SYNOPSIS
#include <sys/scsi/scsi.h>
int prefixtran_reset(struct scsi_address *ap, int level);
INTERFACE LEVEL
Solaris architecture specific (Solaris DDI).
PARAMETERS
ap Pointer to the scsi_address(9S) structure.
level The level of reset required.
DESCRIPTION
The tran_reset() vector in the scsi_hba_tran(9S) structure must be initialized during the HBA driver's attach(9E) to point to an HBA entry
point to be called when a target driver calls scsi_reset(9F).
tran_reset() must reset either the SCSI bus, a SCSI target device, or a SCSI logical unit as specified by level.
level must be one of the following:
RESET_ALL Reset the SCSI bus.
RESET_TARGET Reset the target specified by ap.
RESET_LUN Reset the logical unit specified by ap.
tran_reset should set the pkt_reason field of all outstanding packets in the transport layer associated with each target or logical unit
that was successfully reset to CMD_RESET and the pkt_statistics field must be OR'ed with either STAT_BUS_RESET (if the SCSI bus was reset)
or STAT_DEV_RESET (if the target or logical unit was reset).
The HBA driver should use a SCSI Bus Device Reset Message to reset a target device. The HBA driver should use a SCSI Logical Unit Reset
Message to reset a logical unit.
Packets that are in the transport layer but not yet active on the bus should be returned with pkt_reason set to CMD_RESET and pkt_statis-
tics OR'ed with STAT_ABORTED.
Support for RESET_LUN is optional but strongly encouraged for new and updated HBA drivers. If an HBA driver provides RESET_LUN support, it
must also create the lun-reset capability with a value of zero for each target device instance represented by a valid ap. The HBA is also
required to provide the means to return the current value of the lun-reset capability in its tran_getcap(9E) routine, as well as the means
to change the value of the lun_reset capability in its tran_setcap(9E) routine.
RETURN VALUES
tran_reset() should return:
1 on success.
0 on failure.
SEE ALSO attach(9E), ddi_dma_buf_setup(9F), scsi_hba_attach(9F), scsi_reset(9F), scsi_address(9S), scsi_hba_tran(9S)
Writing Device Drivers
NOTES
If pkt_reason already indicates that an earlier error had occurred for a particular pkt, tran_reset() should not overwrite pkt_reason with
CMD_RESET.
SunOS 5.10 12 Jul 2002 tran_reset(9E)