08-12-2009
basic question on sd.conf and lpc.conf file
Hello Guys,
Do we need to configure this file only if we add SAN disk or even if we add local disk, do we need to modify?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
I want a help for Configuring snmpd.conf and snmptrapd.conf (i.e Configuring SNMP)
for receiving
TRAPS in my networks. I am using RHEL4.0 OS.
Please tell me How I can configure above two files in a proper way and at an
advanced level.
Especially I am getting... (2 Replies)
Discussion started by: jagdish.machhi@
2 Replies
2. UNIX for Dummies Questions & Answers
Folks;
I know this might sounds stupid, but please help with this:
I have share in my smb.conf on my SUSE 10 box.
How can i make this share accessible to outside IP range or a specific IP address without need for user/pass?
Here's the share as it's written in smb.conf:
;
;comment =... (0 Replies)
Discussion started by: Katkota
0 Replies
3. Solaris
Hey all!
I'm working on Solaris10 right now and I was fiddling around with a fresh install and was wondering about the service that uses resolv.conf?
I know prior to Sol10 (SMF) it was /etc/init.d/inetsvc stop and start to reload resolv.conf changes
but I can't seem to find the correct SMF... (5 Replies)
Discussion started by: Keepcase
5 Replies
4. Solaris
OK I am running solaris 10.
I made some changes to my ipf.conf file and issued the command:
ipf -Fa -f /etc/ipf/ipf.conf
to flush out the old and bring in the new changes.
When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see.
I... (3 Replies)
Discussion started by: NewSolarisAdmin
3 Replies
5. Red Hat
What would be Redhat RHEL 4.0 equivalent for Solaris sd.conf and lpfc.conf? What are the files called and where are the files located? (1 Reply)
Discussion started by: soupbone38
1 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I have a question on /etc/syslog.conf file in Solaris 10.
Below is a line taken from /etc/syslog.conf file and I know that the last field (operator) is where the logs gets outputted but how do I find out what the output file name format is going to be and which directory it gets outputted... (1 Reply)
Discussion started by: stevefox
1 Replies
7. UNIX for Advanced & Expert Users
i have this program running on my solaris and there are two identical config files, i am not sure which one is being used by this program but I am sure it uses one of them.
I run lsof -p {pid} but it does not show which config file has been read by this program, what i am doing wrong?
thanks (4 Replies)
Discussion started by: fedora
4 Replies
8. Red Hat
Hi,
I was told to add the "nis" in front of "files" for below lines in /etc/nsswitch.conf was not in a good practise. I tried to search in google and man page for nsswitch.conf and can't find the answer. could someone please help me?
passwd: nis files
shadow: nis files
group: nis files... (2 Replies)
Discussion started by: beeloo
2 Replies
9. Shell Programming and Scripting
Hello all,
Newbie here.
I'm currently tasked with updating rsyslog.conf and auditd.conf on a large set of servers. I know the exact logging configurations that I want to enable. I have updated both files on on a server and hope to use the updated files as a template for the rest of the... (3 Replies)
Discussion started by: Mide
3 Replies
10. Solaris
Hi,
I've installed Solaris 11.3(live media) and configured DNS. Everytime I reboot the server, resolv.conf got deleted and it created a new nsswitch.conf.
I used below to configure both settings:
# svccfg -s dns/client
svc:/network/dns/client> setprop config/nameserver = (xx.xx.xx.aa... (1 Reply)
Discussion started by: flexihopper18
1 Replies
LEARN ABOUT HPUX
vxreattach
vxreattach(1M) vxreattach(1M)
NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS
-b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO
vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)
VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)