|
|
Sponsored Content
Operating Systems
SCO
Problems Detecting HP Tape Drive
Post 302340749 by RicardoM on Tuesday 4th of August 2009 09:24:24 AM
08-04-2009
|
|
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
2. Gentoo
Hello All,
I am pretty new to Linux,
When trying to install TurboLinux 6.0 through a boot floppy,
After a while it says to insert the CD and later it is not recognizing the CDROM,
SO do we need to mount the CD-ROM before installation ??
Thanks in Advance :)
S (13 Replies)
Discussion started by: sbasetty
13 Replies
3. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
4. Solaris
Recently we had a problem with a CPU card on our SunFire V880 which has Solaris 9 OS. we removed the card and there was also a problem with our usr which was accidentally deleted. We able to restore the usr but now we having a problem with our tape drive.
Previously we could write to the with
... (5 Replies)
Discussion started by: rahmantanko
5 Replies
5. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
8. Solaris
Got an informix DB that won't start because DB chunk is offline. Its a raw device. See below:-
lrwxrwxrwx 1 root root 29 Feb 6 2013 /dev/DB -> /devices/pseudo/md@0:0,10,raw
How do I tell what that refers to? I've checked metadb and metastat and cant see any issues? (2 Replies)
Discussion started by: psychocandy
2 Replies
LEARN ABOUT DEBIAN
trm
TRM(4) BSD Kernel Interfaces Manual TRM(4) NAME
trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device trm Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): trm_load="YES" DESCRIPTION
The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC. HARDWARE
SCSI controllers supported by the trm driver include: o Tekram DC-315 PCI Ultra SCSI adapter without BIOS and internal SCSI connector o Tekram DC-315U PCI Ultra SCSI adapter without BIOS o Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector o Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS o Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS o Tekram DC-395U2W PCI Ultra2-Wide SCSI adapter with flash BIOS For the Tekram DC-310/U and DC-390F/U/UW/U2B/U2W/U3W PCI SCSI host adapters, use the sym(4) driver. SEE ALSO
cd(4), ch(4), da(4), intro(4), sa(4), scsi(4), sym(4) http://www.tekram.com/ AUTHORS
The trm driver was originally written for FreeBSD 3.0/i386 by Erich Chen of Tekram Technology, and ported to FreeBSD 5.0 by Olivier Houchard <cognet@FreeBSD.org>. BSD
December 8, 2002 BSD