08-03-2009
ups, sorry... my mistake..
10 More Discussions You Might Find Interesting
1. Solaris
We are installing Solaris 9 with Jumpstart ...facing problems..
Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly.
when we give "boot net - install" at OK prompt, it is coming till
"The system is coming up. Please wait"
After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies
2. Solaris
I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies
3. Solaris
Hi!
I'm trying to skip the installation welcome screen (actually the first three screens: The Solaris Installation Program screen, Identify This System screen and date and time settings - not timezone settings). Everything else runs automaticly from jumpstart except these three screens, just... (6 Replies)
Discussion started by: Luka
6 Replies
4. Solaris
I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following
#more flash_profile_test
install_type flash_install
archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies
5. Solaris
Hi friends ,
i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working.
Now i am planning to use Jumpstart installation method to install my server.
But i... (4 Replies)
Discussion started by: vr_mari
4 Replies
6. Solaris
Hi guys, I have a problem with installing new Solaris servers via jet/jumpstart (tried both).
I`ve configured server, created profile for a client, issued
{1} boot net -v install
and went to get some cofee...
After I came back, client was able to load system from server, get IP and,... (4 Replies)
Discussion started by: masloff
4 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
hello
I created a boot server and tryed to run intstall with jumpstart on other solaris server, but jumpstart coudn't starts, only text-based install. sysidcfg and rules file are in the same shared folder, rules file has only one string
any - - any_profile - and thta't all. also I created... (2 Replies)
Discussion started by: sluge
2 Replies
9. Solaris
Hi
actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies
10. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
LEARN ABOUT REDHAT
snmp-ups
snmp-ups(8) Network UPS Tools (NUT) snmp-ups(8)
NAME
snmp-ups - Driver for RFC 1628 SNMP UPS equipment
NOTE
This man page only documents the hardware-specific features of the snmp-ups driver. For information about the core driver, see nutups-
drv(8).
SUPPORTED HARDWARE
Any UPS that is RFC 1628 (UPS MIB) compliant.
EXPERIMENTAL DRIVER
This driver has been tagged experimental and is not built by default.
REQUIREMENTS
This driver needs UCD SNMP, aka Net-SNMP installed to compile successfully. See http://www.net-snmp.org/ for more information.
On Red Hat 7.2, these packages are required:
ucd-snmp-devel-4.2.3-1, ucd-snmp-4.2.3-1, ucd-snmp-utils-4.2.3-1
You must install SNMP-UPS-MIB.txt in your MIBs directory - typically /usr/share/snmp/mibs/, but it may vary from system to system. You can
generate this from chapter 4 of RFC 1628 (see http://www.faqs.org).
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
community=name
Set community name (default = public)
snmp_version=version
Set SNMP version (default = v1, the other allowed value is v2c)
INSTALLATION
This driver is not built by default. You can build it by using "configure --with-drivers=snmp-ups" before calling make.
IMPLEMENTATION
The hostname of the UPS is specified with the "port" value in ups.conf, i.e.:
[snmp]
driver = snmp-ups
port = snmp-ups.example.com
community = public
snmp_version = v1
SUPPORTED VARIABLES
INFO_MFR UPS Manufacturer
INFO_MODEL UPS Model
INFO_FIRMREV Firmware/Software Version
INFO_STATUS OFF, OL, OB, BOOST, TRIM
INFO_BATTPCT Battery percentage
INFO_RUNTIME Predicted runtime on battery
INFO_BATTVOLT Battery Voltage
INFO_OUTVOLT Output Voltage
PLANNED SUPPORT
INFO_UTILITY Input Voltage
INFO_ACFREQ AC Frequency
INFO_UPSTEM UPS Temperature
INFO_LOADPCT Load Percentage
CMD_? Not determined
AUTHORS
Arnaud Quette, Hans Ekkehard Plesser
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/
NUT mailing list archives and information: http://lists.exploits.org/
Tue Oct 22 2002 snmp-ups(8)