Sponsored Content
Operating Systems Linux Red Hat best config for vmware server Post 302339990 by fpmurphy on Saturday 1st of August 2009 11:45:48 AM
Old 08-01-2009
The type of networking support that you need. NAT, Host only, bridged or custom.
 

4 More Discussions You Might Find Interesting

1. Linux

Help installing VMWARE SERVER 2.0

Hello I am trying to install VMWARE in Ubuntu 8.10 and I have two issues. VMWARE server wants to compile modules to work with my kernel one them gives an error. What do I do: None of the pre-built vsock modules for VMware Server is suitable for your running kernel. Do you want this program... (1 Reply)
Discussion started by: mojoman
1 Replies

2. Red Hat

Minicom with VMWare ESX Server

Hello! I have an ESX Server up and running. Now I want to connect a serial device to the COM Port. For that I need the minicom program. When I try "configure - make - make all" I get some errors. Can someone please explain to me, what the problems are: # ./configure checking for a... (3 Replies)
Discussion started by: Kickbit
3 Replies

3. Linux

VMWare Server on FC13

Can someone provide some assistance with this. I'm trying to install vmware server but it's not going so well. $ uname -a Linux testunix 2.6.33.6-147.2.4.fc13.i686.PAE #1 SMP Fri Jul 23 17:21:06 UTC 2010 i686 i686 i386 GNU/Linux # vmware-config.pl Making sure services for VMware Server are... (1 Reply)
Discussion started by: doublejz
1 Replies

4. AIX

AIX Server - Need to set up VMWare

Hi experts, We are faced with a dilemma - we have a AIX server for educational purposes. We had some Oracle applications running on them. The management decided not to extend the warranty, so we are left with a server that we cannot upgrade immediately. I was wondering if we could set up... (2 Replies)
Discussion started by: ranj@chn
2 Replies
NAT action in tc(8)						       Linux						       NAT action in tc(8)

NAME
nat - stateless native address translation action SYNOPSIS
tc ... action nat DIRECTION OLD NEW DIRECTION := { ingress | egress } OLD := IPV4_ADDR_SPEC NEW := IPV4_ADDR_SPEC IPV4_ADDR_SPEC := { default | any | all | in_addr[/{prefix|netmask}] DESCRIPTION
The nat action allows to perform NAT without the overhead of conntrack, which is desirable if the number of flows or addresses to perform NAT on is large. This action is best used in combination with the u32 filter to allow for efficient lookups of a large number of stateless NAT rules in constant time. OPTIONS
ingress Translate destination addresses, i.e. perform DNAT. egress Translate source addresses, i.e. perform SNAT. OLD Specifies addresses which should be translated. NEW Specifies addresses which OLD should be translated into. NOTES
The accepted address format in OLD and NEW is quite flexible. It may either consist of one of the keywords default, any or all, represent- ing the all-zero IP address or a combination of IP address and netmask or prefix length separated by a slash (/) sign. In any case, the mask (or prefix length) value of OLD is used for NEW as well so that a one-to-one mapping of addresses is assured. Address translation is done using a combination of binary operations. First, the original (source or destination) address is matched against the value of OLD. If the original address fits, the new address is created by taking the leading bits from NEW (defined by the netmask of OLD) and taking the remaining bits from the original address. There is rudimental support for upper layer protocols, namely TCP, UDP and ICMP. While for the first two only checksum recalculation is performed, the action also takes care of embedded IP headers in ICMP packets by translating the respective address therein, too. SEE ALSO
tc(8) iproute2 12 Jan 2015 NAT action in tc(8)
All times are GMT -4. The time now is 03:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy