|
|
Sponsored Content
Operating Systems
SCO
Printing as a CUPS client, only root can print!
Post 302339915 by cyruspy on Friday 31st of July 2009 07:15:51 PM
07-31-2009
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have just installed cup printing software on solaris 8 and i am able to print successfully
from the print server but unable to print from any of the print client in my local network subnet. i have enable browsing so that cups printer server could broadcaste itself to client. but still unable to... (1 Reply)
Discussion started by: hassan2
1 Replies
2. Linux
Hello,
I am using version:
cups-config --version - 1.2.4
However, when i use the -o land or -o landscape command it doesn't print in Landscape.
I have the same problem on another server. (Both running CENTOS).
Does landscape printing work in CUPS? Is there a fix?
Thanks in an... (0 Replies)
Discussion started by: stuaz
0 Replies
3. Slackware
Hello,
Ive got an HP LaserJet 2100 / parallel interface.
I had some troubles getting going due to non-working cups drivers. Updated cups and also used a .ppd.gz file from something HP provided. found the files here...
www.linuxprinting.org/show_printer.cgi?recnum=HP-LaserJet_2100
Anyways.... (1 Reply)
Discussion started by: agentrnge
1 Replies
4. Linux
Hi all.
I have a problem with some printers that when I print a lot of jobs at once the printers gets stuck after 2 prints... (It's a barcode printers - DATAMAX).
Whenever I'm printing each job separtly with a delay of a few seconds the printers work fine...
So my question is how can I... (0 Replies)
Discussion started by: eliraza6
0 Replies
5. AIX
Hello all.
I am setting up a queue under AIX 4.2.1 to print to a remote Linux CUPS queue. At present I can print to the queue remotely from Windows but not AIX. What I am seeing is lpstat reads the state of the remote queue but at job submission time I am getting backend exit fatal errors. The... (4 Replies)
Discussion started by: tgx
4 Replies
6. UNIX for Advanced & Expert Users
I ported application from SysV to Linux and run into troubles with printing.
Application uses lp and HP JetDirect-based printers, it inserts HP control codes in the file and uses plain lp -d dest doc-file command to print it.
The Linux (Ubuntu 8) has CUPS system, which I am not familiar... (0 Replies)
Discussion started by: migurus
0 Replies
7. Red Hat
Hi all,
unable to print from linux box. Earlier it used to work fine.
The print job is sitting in the queue and not going to printer.
Removed queue job and tried again but no luck.
Tried "cupsenable" but ended up with no success.
I tried to print two text files as "root" with "lp " command... (0 Replies)
Discussion started by: lramsb4u
0 Replies
8. UNIX for Advanced & Expert Users
Hi Guys,
I've inherited a mess of an infrastructure in my new job, there hasn't been a sys admin in post for about a year, so things are falling apart. The first thing to break after I started was the printer server. I have it working again, and people can print, however it's very slow, slower... (0 Replies)
Discussion started by: rudigarude
0 Replies
9. Red Hat
Hi All,
Having searched for a solution to this issue i found no suggestions which help my particular problem.
I am getting the following error message on 1 of the 3 printers i have configured:
recoverable: Network host 'xxx.xxx.xxx.xxx' is busy; will retry in 30 seconds
All 3 printers are... (0 Replies)
Discussion started by: Tommyk
0 Replies
10. UNIX for Advanced & Expert Users
Hello Experts,
I have been facing an issue with printing through cups configured on Linux server.
All was going on well but all of a sudden the printers started giving an error message, "Unsupported format application/postscript!" and we cant get any prints of any printer.
Need your help as... (2 Replies)
Discussion started by: Rockyc3400
2 Replies
LEARN ABOUT SUNOS
accept
accept(1M) System Administration Commands accept(1M) NAME
accept, reject - accept or reject print requests SYNOPSIS
accept destination... reject [-r reason] destination... DESCRIPTION
accept allows the queueing of print requests for the named destinations. reject prevents queueing of print requests for the named destinations. Use lpstat -a to check if destinations are accepting or rejecting print requests. accept and reject must be run on the print server; they have no meaning to a client system. OPTIONS
The following options are supported for reject: -r reason Assigns a reason for rejection of print requests for destination. Enclose reason in quotes if it contains blanks. reason is reported by lpstat -a. By default, reason is unknown reason for existing destinations, and new printer for destinations added to the system but not yet accepting requests. OPERANDS
The following operands are supported. destination The name of the destination accepting or rejecting print requests. Destination specifies the name of a printer or class of printers (see lpadmin(1M)). Specify destination using atomic name. See printers.conf(4) for information regarding the naming conventions for atomic names. EXIT STATUS
The following exit values are returned: 0 Successful completion. non-zero An error occurred. FILES
/var/spool/lp/* LP print queue. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWpcu | +-----------------------------+-----------------------------+ |CSI |Enabled (see NOTES) | +-----------------------------+-----------------------------+ SEE ALSO
enable(1), lp(1), lpstat(1), lpadmin(1M), lpsched(1M), printers.conf(4), attributes(5) NOTES
accept and reject affect only queueing on the print server's spooling system. Requests made from a client system remain queued in the client system's queueing mechanism until they are cancelled or accepted by the print server's spooling system. accept is CSI-enabled except for the destination name. SunOS 5.10 8 Feb 1999 accept(1M)