I had been using a modem installed on a Digi accelerator port to dial in to an SCO open server r5 server. On monday it quit working and I realy don't know how it was installed and configured. I have tested the modem on a PC and it works. The port the modem is connected to is ttyB06 and I have... (1 Reply)
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
HI all,
i still have a problem when using null modem to see the output from my server(sun ultra en 3000).
i followed the instruction from the internet, but it is not working.
1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port).
2.... (3 Replies)
I have a serial modem connected to a usb port using an adapter cable. The system is a HP DL360. RedHat ES3.0
I am using the device /dev/ttyUSB0
When I issue the command "mgetty ttyUSB0" I get the following output in the log file.
How do I get the system to see the modem.
12/02 14:17:55... (2 Replies)
Hi,
I'm having a issue on communicating the serial GSM modem in Sun Solaris 5.9
To implement such connectiom, i'm using the "tip -115200 /dev/term/a" command and i successfully get the "connected" status
And then i send a "AT" message and receive "OK" response from the modem :D
Anyhow,... (0 Replies)
I have serial modem connection between two computers. We have to login the remote computer through ip address. How can I get the ip address in this connection? (1 Reply)
I currently access a remote Unix server which has an external modem connected to one of it's serial ports (/dev/cua/b). At times, this server undergoes a hard reset and for some reason this disallows us from making use of the modem any longer. A hard reset of the modem always seems to fix the... (0 Replies)
Hello,
I want to connect a VT520 terminal to p3 linux box.
I have two questions regarding the connection. First,
is it possible to use RJ45 instead of RS232
cable. (with DB9 pin to RJ45 and DB25 to RJ45 converter).
Second point is that; do i need null modem cable or
straight cable... (5 Replies)
Hello everybody,
I didn't know were to post this, so i posted here in hardware section.
I'm having some troubles while trying to interconnect two pc's via modem (soft fax modem, RJ-11 jack). One is a Handheld PC (HP Jornada 728) with a single fax modem slot, and the other computer is a PC with... (6 Replies)
In ubuntu etopic i create this udev rules for prolink 3g usb modem:
SUBSYSTEM=="block",
SUBSYSTEM=="scsi",
ATTRS{idVendor}=="1e0e",
ATTRS{idProduct}=="f000",
ACTION=="add",
RUN+="/sbin/modprobe usbserial Vendor=0X1e0e Product=0Xf000"
After plugging the usb modem, ubuntu assigns the ports... (4 Replies)
Discussion started by: shamsat
4 Replies
LEARN ABOUT REDHAT
serial_cs
SERIAL_CS(4) Kernel Interfaces Manual SERIAL_CS(4)NAME
serial_cs - PCMCIA serial port driver
SYNOPSIS
insmod serial_cs.o [pc_debug=n] [irq_list=i,j,...] [do_sound=n]
DESCRIPTION
Serial_cs is the Card Services driver for all PCMCIA serial devices, including modem cards. When serial_cs is bound to a serial or modem
card, it will generally attempt to allocate the first unused serial device for use by the card. The device chosen will be recorded in the
kernel log file, and will also be reported to cardmgr(8). The major and minor numbers and device name reported by serial_cs will match the
corresponding "dialout" device (/dev/cua#). The new device can be accessed using this device file or the corresponding /dev/ttyS# device.
The default serial card setup script will link the dialout device to /dev/modem.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
do_sound=n
A flag specifying if speaker output should be enabled. The default is 1 (true). Set to 0 to disable speaker output.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:48 SERIAL_CS(4)