07-26-2009
I have LUN ID, how to find disk relate to that LUN ID?
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hi,
i have a volume on a LUN of an EMC-storage and i need to increase the
size.
i could increase the size of the LUN on the EMC, i could increase the
size of the disk for solaris, but how can i tell the veritas volume
manager that the disk is larger now?
what i've done:
1. LUN on EMC
2.... (3 Replies)
Discussion started by: pressy
3 Replies
2. Solaris
I just installed IBMsdd on Solaris diver along with the patches recommended. I also installed 2 - 2Gigs qlogic fiber cards & the corresponding pkges for the cards.
What command can I use to scan this LUN disks from my Soalris servers. Solaris doen't seem to be seeing this disks presented on it.... (2 Replies)
Discussion started by: Remi
2 Replies
3. Solaris
hey guys i got this in my logs what does this mean: (1 Reply)
Discussion started by: sbn
1 Replies
4. AIX
Hello guys,
It would be so nice of you if someone can provide me with these informations.
1) My SAN group assigned 51G of LUN space to the VIO server.I ran cfgdev to discover the newly added LUN. Unfortunately most of the disks that are in VIO server is 51G. How would I know which is the newly... (3 Replies)
Discussion started by: solaix14
3 Replies
5. Solaris
Hello all,
I need find in my OS (Sun10) on LUN 1Tb with WWN 6005-08b4-0010-7137-0000-e000-0076-0000 (HBA)
How do it?,
Thanks, (3 Replies)
Discussion started by: aav1307
3 Replies
6. HP-UX
HI all,
I am confused when I am seeing the output of bdf command ioscan -fnC disk, there is no same files which i have seen in bdf output and ioscan output...One volume was mounted in one folder called /teldb and device file path was /dev/disk/disk48. The same i didnt found in ioscan disk... (6 Replies)
Discussion started by: selvaforum
6 Replies
7. AIX
Hi,
I am not getiting lun id information on VIO Server. I have used the command fget_config command.
just showing # prompt.
I would like know wheather any other command is there equiv of fget_config
which will display lun id? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
8. Solaris
Dear all,
i want to get the LUN ID for some disks in solaris 10
what commands options for the MPXIO and inq i want these utilities only
because i don't have solution enabler or powerpath
BR, (1 Reply)
Discussion started by: maxim42
1 Replies
9. UNIX for Dummies Questions & Answers
how do I know which hdisk from "lsdev -Cc disk" is my LUN on NetApp after zoning from SAN switch?
is it "MPIO other FC SCSI Disk Drive"? (1 Reply)
Discussion started by: malayo
1 Replies
10. HP-UX
Hello folks,
I have Hp.ux 11.31 and I need know how formating in OS new LUN disk attach to system
e.g. the wwid:
# scsimgr lun_map -D /dev/rdisk/disk4
LUN PATH INFORMATION FOR LUN : /dev/rdisk/disk4
Total number of LUN paths = 2
World Wide Identifier(WWID) =... (3 Replies)
Discussion started by: aav1307
3 Replies
LEARN ABOUT NETBSD
scan_lfs
SCAN_FFS(8) BSD System Manager's Manual SCAN_FFS(8)
NAME
scan_ffs, scan_lfs -- find FFSv1/FFSv2/LFS partitions on a disk or file
SYNOPSIS
scan_ffs [-blv] [-e end] [-F file] [-s start] device
DESCRIPTION
scan_ffs will take a raw disk device that covers the whole disk or a file and will find all possible FFSv[12]/LFS partitions, independent of
block sizes on it. It will show the file system type (FFSv1, FFSv2, or LFS), size, and offset. Also it has an option to show the values
with a disklabel-alike output.
The options are as follows:
-b Report every superblock found with its sector address, rather than trying to report the partition boundaries. This option can
be useful to find the other superblocks in a partition if the first superblock has become corrupted. It is most useful if
device refers to the raw device for the partition, rather than the entire disk.
-e end Where to stop searching for file systems. The end argument specifies the last sector that will be searched. Default is the
last sector of device.
-F file Path to a file containing possible partitions inside of it.
-l Print out a string looking much like the input to disklabel. With a little massaging, this output can usually be used by
disklabel(8).
-s start Where to start searching for file systems. This makes it easier to skip swap partitions or other large non-UFS/FFS partitions.
The start argument specifies the first sector that will be searched. Default is the first sector of device.
-v Be verbose about what scan_ffs is doing, and what has been found.
The device argument specifies which device scan_ffs should scan for file systems.
scan_lfs is just another name for the same program, both behave in exactly the same way.
SEE ALSO
disklabel(8)
HISTORY
The scan_ffs program first appeared in OpenBSD 2.3 and then in NetBSD 3.1. Support for searching in files was added in NetBSD 4.0.
AUTHORS
scan_ffs was written for OpenBSD by Niklas Hallqvist and Tobias Weingartner. It was ported to NetBSD by Juan Romero Pardines, who added sup-
port for LFS/FFSv2, partitions with fragsize/blocksize greater than 2048/16384 for FFSv1, searching on files, etc.
BUGS
Currently scan_ffs won't find partitions with fragsize/blocksize greater than 8192/65536.
BSD
May 1, 2007 BSD