Hi all,
I need to syncronize a Solaris client with a QNX Server, modifying the client date, I need any alternative to set the sistem date (client Solaris) but i can't use commands date -a XXX (XXX are the time in seconds) and can't use rdate and ntp.
How can I do It? :confused: (2 Replies)
Is there a way to set a system variables length? We are running on HP/UX using ksh.
I have a variable length system variable but I always want the length to be 15. Currently we append using sed 15 characters to the end of the variable and then cut -c 1-15. Looking for a better way. (2 Replies)
Hi,
I try to run a script on remote systems with ssh
it should execute a command, read values from stdout, use it as input for a loop
and works with this variable on remote system
but the variable isn't working, I guess because export, echo , or the loop itself are shell builtins and not... (2 Replies)
Hi,
I recently swapped the ethernet port that my Sun Fire v240 was using and back again to test a different connection. I didn't anticiapte any major problems to be caused by this.
However, after a reboot, I am now stuck in a boot loop with the following errors:
forceload of drv/qus... (6 Replies)
What are the server requirements, Software requirements, Network requirements etc,
Please help me.. as 'm new 'm unable to get things done @ my end alone.
Please refrain from typing subjects completely in upper case letters to get more attention, ty. (5 Replies)
Can u please help me in knowing the details of the servers needed,
FIBRE CABLES, HA softwares, VIO Softwares and other details.
I googled through out and couldnt get a clear idea of it. Please help me (6 Replies)
Dear All
I am trying to write a script to set the SGE job execution order. I named each job with 'job1', 'job2' and 'job3'. I want my script to do: When 'job1' execution is complete, 'job2' is executed; when both 'job1' and 'job2' are complete, 'job3' is executed.
First, I tried this... (0 Replies)
Default file system currently is 664.
I would like to get it as 774.
As other users of the same group was not able execute the file created any any user.
chmod cannot be used in my case. (Files are created and executed the programs owned by different vendors)
we know that umask is not going... (3 Replies)
Hi,
I have a Sun-Fire-V440 server.
I want to set IP address for its LOM from operating system.
Earlier it does not have any IP address.
Is it possible to set IP from Operating System ?
if possible, how can we do it ?
Thanks
Sri (3 Replies)
Does anyone know if it's possible to specify the mount order of local and remote file systems? I'd like to mount a local ZFS file system on top of an NFS mount automatically and have that repeated on every reboot.
I've checked man pages and Google, but can't find anything that addresses,... (6 Replies)
Discussion started by: Monty51
6 Replies
LEARN ABOUT HPUX
sysdef
sysdef(1M)sysdef(1M)NAME
sysdef - display system definition
SYNOPSIS
[kernel [master]]
DESCRIPTION
Note: will not be supported in future releases of HP-UX (refer to section below). So users are advised to use the kctune(1M) utility which
provides additional information on kernel tunable parameters.
The command analyzes the currently running system and reports on its tunable configuration parameters. kernel and master are not used, but
can be specified for standards compliance.
For each configuration parameter, the following information is printed:
The name and description of the parameter.
The current value of the parameter.
The value of the parameter at boot time, if different from the
current value.
The minimum allowed value of the parameter, if any.
The maximum allowed value of the parameter, if any.
Where appropriate, the units by which the parameter is measured.
Flags that further describe the parameter. The following flag
is defined:
Parameter can be modified without rebooting.
WARNINGS
Users of must not rely on the exact field widths and spacing of its output, as these will vary depending on the system, the release of HP-
UX, and the data to be displayed.
is provided for compatibility purposes only and is no longer maintained since being marked for obsolescence in a future HP-UX release. The
output from is known to be incorrect when reporting values for some tunable parameters such as and
SEE ALSO kctune(1M).
TO BE OBSOLETED sysdef(1M)