|
|
Sponsored Content
Operating Systems
Solaris
jumpstart installation
Post 302337335 by nitin on Thursday 23rd of July 2009 11:42:34 PM
07-24-2009
Also, jumpstart for SPARC and x86 are different 
. I did a post long time ago, I refer it from time to time. Here you go.
SPARC is pretty much fully automated, x86 has some limitations.
HTH,
-Nitin
. I did a post long time ago, I refer it from time to time. Here you go.SPARC is pretty much fully automated, x86 has some limitations.
HTH,
-Nitin
|
|
10 More Discussions You Might Find Interesting
1. Solaris
We are installing Solaris 9 with Jumpstart ...facing problems..
Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly.
when we give "boot net - install" at OK prompt, it is coming till
"The system is coming up. Please wait"
After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies
2. Solaris
I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies
3. Solaris
Hi!
I'm trying to skip the installation welcome screen (actually the first three screens: The Solaris Installation Program screen, Identify This System screen and date and time settings - not timezone settings). Everything else runs automaticly from jumpstart except these three screens, just... (6 Replies)
Discussion started by: Luka
6 Replies
4. Solaris
I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following
#more flash_profile_test
install_type flash_install
archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies
5. Solaris
Hi friends ,
i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working.
Now i am planning to use Jumpstart installation method to install my server.
But i... (4 Replies)
Discussion started by: vr_mari
4 Replies
6. Solaris
Hi guys, I have a problem with installing new Solaris servers via jet/jumpstart (tried both).
I`ve configured server, created profile for a client, issued
{1} boot net -v install
and went to get some cofee...
After I came back, client was able to load system from server, get IP and,... (4 Replies)
Discussion started by: masloff
4 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
hello
I created a boot server and tryed to run intstall with jumpstart on other solaris server, but jumpstart coudn't starts, only text-based install. sysidcfg and rules file are in the same shared folder, rules file has only one string
any - - any_profile - and thta't all. also I created... (2 Replies)
Discussion started by: sluge
2 Replies
9. Solaris
Hi
actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies
10. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
LEARN ABOUT OPENSOLARIS
pcan
pcan(7D) Devices pcan(7D) NAME
pcan - Cisco Aironet 802.11b wireless NIC driver DESCRIPTION
The pcan wireless NIC driver is a multi-threaded, loadable, clonable, GLDv3-based STREAMS driver. It supports the pccard and PCI/MiniPCI cards with the Cisco Aironet 802.11b chipset. For pccard, the driver works in both SPARC and x86 (32-bit/64-bit) modes. For PCI/MiniPCI card, the driver works in 32-bit x86 mode only. DRIVER CONFIGURATION
The pcan driver supports 802.11b data rates of 1, 2, 5.5 and 11 (Mbits/sec). The default is 11. The pcan driver supports BSS networks (also known as "ap" or "infrastructure" networks) and IBSS networks (also known as "ad-hoc" net- works). For authentication type, the pcan driver supports the "open" (or "open-system") mode. For encryption type, only WEP is currently supported. You perform configuration and administration tasks using the dladm(1M) and wificonfig(1M) utilities. FILES
/dev/pcan* Special character device. /kernel/drv/pcan 32-bit ELF kernel module (x86). /kernel/drv/amd64/pcan 64-bit ELF kernel module (x86). /kernel/drv/sparcv9/pcan 64-bit ELF kernel module (SPARC). ATTRIBUTES
See attributes(5) for a description of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SPARC, x86 | +-----------------------------+-----------------------------+ SEE ALSO
dladm(1M), wificonfig(1M), attributes(5), gld(7D) 802.11b Standard for Wireless Local Area Networks (WLANs) - IEEE SunOS 5.11 24 Jan 2007 pcan(7D)