07-21-2009
AIX 4.2 with a 10Gb or 100Gb connection.....no!
Think again and post what you really have, 10Mb and 100Mb by any chance?
9 More Discussions You Might Find Interesting
1. AIX
Hello all,
Anyboby knows what is the reason by which the ouput of the command mt -f /dev/rmt0.1 status on AIX does not show the same information that in the rest of platforms UNIX (Solaris, HP-UX, ...)?
Then, what command of AIX is similar to mt- f /dev/rmt0.1 status of Solaris? We need it to... (0 Replies)
Discussion started by: smoraprosol
0 Replies
2. UNIX Desktop Questions & Answers
Ok now is one is a reall dummy question...:rolleyes:
I'm using KDE 3.3 and I want to know if there are any way to set the option where
when I point(a cursor) to a window that window becomes active. Juust as you have in Solaris.
Thanks & regards, (1 Reply)
Discussion started by: rimser9
1 Replies
3. UNIX for Advanced & Expert Users
I need to execute a script from dev server which is located on Test server.I can use ftp to connect to dev server and from there how can i execute a command on test server.
Thanks (5 Replies)
Discussion started by: ukatru
5 Replies
4. AIX
I am trying to find a way to do the following on an AIX 4.2 with Korn:
tar cvfpdl - . | compress > /dev/rmt0
The /dev/rmt0 is the device we use when we tar directly to it.
I want to compress a folder's content to tape. Our current TAR does not have compression at all. We only have... (5 Replies)
Discussion started by: Browser_ice
5 Replies
5. AIX
I want to compress backup files to tape using compress on our AIX 4.2
- Our TAR does not have compression.
- I do not want to use local storage to compress as most of the filesystems are pretty full.
- the only compressing tool we have is 'compress'
- tapes are 5Gb 8mm
I am trying this... (10 Replies)
Discussion started by: Browser_ice
10 Replies
6. Solaris
Hello,
I have a centos as nfs server, its name is centos_A.
After I finish the setup of the nfs server, the other linux can access this nfs server immediately via /net/centos_A/*
But,
My solaris 9 can not access /net/centos_A/* immediately. I have to leave /net/centos_A, and wait for about... (1 Reply)
Discussion started by: bruceharbin
1 Replies
7. Shell Programming and Scripting
hi, i am new to unix,
cuold u send some sftp acripts to send files to dev server to clint server, (1 Reply)
Discussion started by: Koti.annam
1 Replies
8. AIX
Dear all
First of all, my English not so good.
We have p52a (production server) and p52a (test server). Tape drives are VXA2.
When both servers were AIX 5.3, mksysb on production server and restoring to test server was OK.
The production server was AIX 5.3 and recently upgraded to... (3 Replies)
Discussion started by: fifa15pc
3 Replies
9. AIX
Hi 2 ALL,
try to run NFS Server in AIX 7.1 :
1. Step by step on NFS Server node
mkdir /tmp/test
chgrp staff /tmp/test
chmod 775 /tmp/test-- create export directory (fs)
mknfsexp -d /tmp/test -t ro
exportfs -va
show mount -e
:/# exportfs -av
exports: 1831-187 re-exported /tmp/test... (4 Replies)
Discussion started by: penchev
4 Replies
LEARN ABOUT OPENSOLARIS
txp
TXP(4) BSD Kernel Interfaces Manual TXP(4)
NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)
HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD
March 12, 2009 BSD