R128(4x)																  R128(4x)

NAME

       r128 - ATI Rage 128 video driver

SYNOPSIS

       Section "Device"
	 Identifier "devname"
	 Driver "r128"
	 ...
       EndSection

DESCRIPTION

       r128 is an Xorg driver for ATI Rage 128 based video cards.  It contains full support for 8, 15, 16 and 24 bit pixel depths, hardware accel-
       eration of drawing primitives, hardware cursor, video modes up to 1800x1440 @ 70Hz, doublescan modes (e.g.,  320x200  and  320x240),  gamma
       correction  at all pixel depths, a fully programming dot clock and robust text mode restoration for VT switching.  Dualhead is supported on
       M3/M4 mobile chips.

SUPPORTED HARDWARE

       The r128 driver supports all ATI Rage 128 based video cards including the Rage Fury AGP 32MB, the XPERT 128 AGP 16MB and the XPERT  99  AGP
       8MB.

CONFIGURATION DETAILS

       Please refer to xorg.conf(5) for general configuration details.	This section only covers configuration details specific to this driver.

       The  driver  auto-detects  all device information necessary to initialize the card.  However, if you have problems with auto-detection, you
       can specify:

	   VideoRam - in kilobytes
	   MemBase  - physical address of the linear framebuffer
	   IOBase   - physical address of the MMIO registers
	   ChipID   - PCI DEVICE ID

       In addition, the following driver Options are supported:

       Option "SWcursor" "boolean"
	      Selects software cursor.	The default is off.

       Option "NoAccel" "boolean"
	      Enables or disables all hardware acceleration.  The default is to enable hardware acceleration.

       Option "Dac6Bit" "boolean"
	      Enables or disables the use of 6 bits per color component when in 8 bpp mode (emulates VGA mode).  By default, all 8 bits per  color
	      component are used.  The default is off.

       Option "VideoKey" "integer"
	      This overrides the default pixel value for the YUV video overlay key.  The default value is undefined.

       Option "Display" "string"
	      Select display mode for devices which support flat panels. Supported modes are:

	      "FP" - use flat panel;

	      "CRT" - use cathode ray tube;

	      "Mirror" - use both FP and CRT;

	      "BIOS" - use mode as configured in the BIOS.

	      The default is FP.

       The following Options are mostly important for non-x86 architectures:

       Option "ProgramFPRegs" "boolean"
	      Enable  or  disable  programming of the flat panel registers.  Beware that this may damage your panel, so use this at your own risk.
	      The default depends on the device.

       Option "PanelWidth" "integer"

       Option "PanelHeight" "integer"
	      Override the flat panel dimensions in pixels. They are used to program the flat panel registers and normally  determined	using  the
	      video card BIOS. If the wrong dimensions are used, the system may hang.

       Option "UseFBDev" "boolean"
	      Enable  or disable use of an OS-specific framebuffer device interface (which is not supported on all OSs).  See fbdevhw(4x) for fur-
	      ther information.  Default: on for PowerPC, off for other architectures.

       Option "DMAForXv" "boolean"
	      Try or don't try to use DMA for Xv image transfers. This will reduce CPU usage when playing big videos  like  DVDs,  but	may  cause
	      instabilities.  Default: off.

       The following additional Options are supported:

       Option "ShowCache" "boolean"
	      Enable or disable viewing offscreen cache memory.  A development debug option.  Default: off.

       Option "VGAAccess" "boolean"
	      Tell the driver if it can do legacy VGA IOs to the card. This is necessary for properly resuming consoles when in VGA text mode, but
	      shouldn't be if the console is using radeonfb or some other graphic mode driver. Some platforms like PowerPC have issues with those,
	      and  they  aren't  necessary  unless  you  have a real text mode in console. The default is off on PowerPC and SPARC and on on other
	      architectures.

       Dualhead Note: The video BIOS on some laptops interacts strangely with dualhead.  This can result in flickering and problems changing modes
       on  crtc2.   If	you  experience  these	problems try toggling your laptop's video output switch (e.g., fn-f7, etc.) prior to starting X or
       switch to another VT and back.

SEE ALSO

       Xorg(1), xorg.conf(5), xorgconfig(1), Xserver(1), X(7)

AUTHORS

       Rickard E. (Rik) Faith	faith@precisioninsight.com
       Kevin E. Martin		kevin@precisioninsight.com

X Version 11						       xf86-video-r128 6.8.0							  R128(4x)