07-20-2009
Yup, Solaris 9.
Thanks.
I solved the error by doing a newfs on it.
I'm having whole lots of problems setting up the server.
Can i ask how do i check the configuration (what type of RAID is setup) on external hard disk (StorEdge A1000) through Enterprise 450 Server?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am running mandrake 8.2 and when booting I get the message:
e2fschk: Bad magic number in super-block while trying to open /dev/hda8.
The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and really contains a valid an ext2 filesystem (and... (1 Reply)
Discussion started by: Jay
1 Replies
2. UNIX for Advanced & Expert Users
Hi,
when installing a piece of third part software I get the error "Bad magic number" at one point when it tries to use libraries from the bea tuxedo server. Am I correct that this means that the software is expecting 32bit while I'm on 64bit? Is there a way around it or can it only be solved... (5 Replies)
Discussion started by: rein
5 Replies
3. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
4. HP-UX
Error received when I tried to restore a blank disk with an 'auto recovery' DDS tape via HP-UX recovery system 2.0 onto a 1Gb SCSI. I assumed it would do the setup, wrong. Could someone tell me the procedure to initial disk for recovering files using cpio. The system is a HP-UX 9.04 version on a... (1 Reply)
Discussion started by: admin wanabee
1 Replies
5. Filesystems, Disks and Memory
I had a power outage a day ago and when the power came back on my FreeBSD 4.6 webserver had problems. It said it was unable to mount /var and made me start in single user mode and said to run fsck MANUALY. So i did and this is now what i get.
www# fsck /dev/ad0s1e
** /dev/ad0s1e
BAD SUPER... (4 Replies)
Discussion started by: matthewbane
4 Replies
6. Solaris
I want mount a disk. I have this error. I'm trying to correct with the superblock but i have the same error. Look my procedure.
bash-2.03# fsck -F ufs /dev/rdsk/c0t1d0s0
Alternate super block location: 9423392.
** /dev/rdsk/c0t1d0s0
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE... (1 Reply)
Discussion started by: simquest
1 Replies
7. Solaris
/pci@if,0/pci@1,1/ide@3/dad@0,0 corrupt label wrong magic number
can u plz suggustion me (6 Replies)
Discussion started by: tirupathi
6 Replies
8. Solaris
I'll keep it fairly straight forward. I work with a Solaris server and magically today it decided to take a dump on me. At first it give a long list of files that couldn't be acessed before terminating the boot process and returning to the 'ok' prompt. Booting in single-user mode allowed me to run... (4 Replies)
Discussion started by: Aon
4 Replies
9. Filesystems, Disks and Memory
Hello all,
I have a hard drive that I can't repair.
The drive is WD15EARS - Filesystem ext4 ( not 100% sure )
It's used in a Synology DS110j NAS.
I try to run fsck -p /dev/sdb on the HD and I get this:
Bad magic number in super-block while trying to open /dev/sdb
/dev/sdb:
The superblock... (4 Replies)
Discussion started by: dallasw1983
4 Replies
10. Solaris
So we have a new to us v240 server with no OS installed. It has an outdated version of OB and ALOM so before we install the OS we want to update both. We have a DVD with the latest OB patch burned on it.
We do the boot cdrom command but receive the Bad Magic Number Error. Does an OS need to... (2 Replies)
Discussion started by: dunkpancakes
2 Replies
LEARN ABOUT HPUX
vxr5check
vxr5check(1M) vxr5check(1M)
NAME
vxr5check - verify RAID-5 volume parity
SYNOPSIS
/etc/vx/bin/vxr5check [-i | -v] [-g diskgroup] volume
DESCRIPTION
The vxr5check utility compares the parity of each stripe of a RAID-5 volume specified by volume. vxr5check reads the data for each stripe,
generates the parity for this stripe, and compares this parity with the existing parity.
vxr5check can be run against the entire RAID-5 volume, or incrementally on RAID-5 stripe boundaries, by specifying the -i option.
OPTIONS
-g diskgroup
Specifies the Veritas Volume Manager (VxVM) disk group name for the RAID-5 volume name for verification. If this option is not
specified, the default disk group is determined using the rules given in the vxdg(1M) manual page.
-i Verifies the RAID-5 volume incrementally per stripes. If a parity mismatch is found, that stripe location is displayed.
-v Verbose output for the incremental vxr5check verification. The verbose option outputs each stripe number that is being verified.
OUTPUT FORMAT
In verbose mode and incremental mode, summary reports for each stripe of the RAID-5 volume are printed in output records. If an error is
returned for a stripe, then an error message and stripe number are displayed. In non-verbose mode, if an error is returned, an error mes-
sage is displayed.
If a parity mismatch error is determined on a stripe, vxr5check exits on that stripe and does not continue for the remaining stripes in the
RAID-5 volume.
FILES
/usr/lib/vxvm/bin/vxr5vrfy The utility that vxr5check calls to perform RAID-5 parity verification operations for the specified RAID-5
volume.
EXIT CODES
The vxr5check utility exits with a non-zero status if the attempted operation fails. A non-zero exit code is not a complete indicator of
the problems encountered, but rather denotes the first condition that prevented further execution of the utility.
See vxintro(1M) for a list of standard exit codes.
NOTES
Do not run vxr5check on a volume that is in degraded mode.
SEE ALSO
vxevac(1M), vxintro(1M), vxmend(1M), vxvol(1M)
VxVM 5.0.31.1 24 Mar 2008 vxr5check(1M)