Hi. i dont think its related to that volume from zfs.
ex:/
Configure a service exporting tank1/myvol as a virtual disk:
host1# /opt/SUNWldm/bin/ldm add-vdiskserverdevice /dev/zvol/rdsk/tank1/myvol zvol@primary-vds0
Add the exported disk to domain (domain2 in this example):
Dear Srs,
I have a Linux server (linux01) booting from SAN with a volume in a Nexsan SATAbeast storage array (san01). The disk/volume has four ext3 partitions, total size is near to 400GB, but only 20-30GB are in use.
I need to move this disk/volume to another Nexsan SATAbeast storage array... (0 Replies)
Hi,
We have 200GB SAN volume mounted on Redhat EL 5. which is working fine. As my SAN supports dynamic resizing of volumes, i unmounted the volume and resized the SAN Volume to 300 GB successfully. Then i mounted again but it shows 200GB only but data is intact.
Now, my requirement is to let... (3 Replies)
Hello all. I have a perplexing problem
I have an AIX 5.1 system on an EMC SAN.
This system had been on a CX400 SAN for several years. The system was migrated to a CX700 just over a week ago. The migration consisted of utilizing on of the HBAs in the system and connecting to both SANs
... (9 Replies)
Hi, I need to expand a ZFS volume from 500GB to 800GB. I'd like to ask your help to confirm the following procedure:
Can I do it on the fly without bothering the users working on this volume?
Thank you in advance! (6 Replies)
I have viewed a few previous posts regarding this, but none of them quite described or worked with my issue.
I am out of local disk space on my LDOM Manager but still have plenty of SAN vCPU and Memory available so I am trying to install a new LDOM OS on SAN.
I have exposed the SAN to the... (0 Replies)
Apologies if this is the wrong forum..
I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Hi all,
I'm using Solaris 11.3.
HBA port connected to SAN disk 3T.
AVAILABLE DISK SELECTIONS:
0. c0t600A0B800033696A0000214B571938F1d0 <SUN-CSM200_R-0760 cyl 44556 alt 2 hd 255 sec 189>
/scsi_vhci/ssd@g600a0b800033696a0000214b571938f1
1. c2t3C58620E0C565100d0... (1 Reply)
Generally, this is what we do:-
On primary, export 2 LUNs (add-vdsdev).
On primary, assign these disks to the ldom in question (add-vdisk).
On ldom, created mirrored zpool from these two disks.
On one server (which is older) we have:-
On primary, create mirrored zpool from the two LUNs.... (4 Replies)
Discussion started by: psychocandy
4 Replies
LEARN ABOUT DEBIAN
amzfs-snapshot
AMZFS-SNAPSHOT(8) System Administration Commands AMZFS-SNAPSHOT(8)NAME
amzfs-snapshot - Amanda script to create zfs snapshot
DESCRIPTION
amzfs-snapshot is an Amanda script implementing the Script API. It should not be run by users directly. It create a zfs snapshot of the
filesystem where the path specified is mounted.
PRE-DLE-* create a snapshot and the POST-DLE-* destroy the snapshot, *-DLE-AMCHECK, *-DLE-ESTIMATE and *-DLE-BACKUP must be set to be
executed on the client:
execute-on pre-dle-amcheck, post-dle-amcheck, pre-dle-estimate, post-dle-estimate, pre-dle-backup, post-dle-backup
execute-where client
The PRE_DLE_* script output a DIRECTORY property telling where the directory is located in the snapshot. The application must be able to
use the DIRECTORY property, amgtar can do it.
The script is run as the amanda user, it must have the priviledge to create and destroy snapshot:
zfs allow -ldu AMANDA_USER mount,snapshot,destroy FILESYSTEM
Some system doesn't have "zfs allow", but you can give the Amanda backup user the rights to manipulate ZFS filesystems by using the
following command:
usermod -P "ZFS File System Management,ZFS Storage Management" AMANDA_USER
This will require that your run zfs under pfexec, set the PFEXEC property to YES.
The format of the DLE must be one of:
Desciption Example
-----------------
Mountpoint /data
Arbitrary mounted dir /data/interesting_dir
ZFS pool name datapool
ZFS filesystem datapool/database
ZFS logical volume datapool/dbvol
The filesystem must be mounted.
PROPERTIES
This section lists the properties that control amzfs-snapshot's functionality. See amanda-scripts(7) for information on the Script API,
script configuration.
DF-PATH
Path to the 'df' binary, search in $PATH by default.
ZFS-PATH
Path to the 'zfs' binary, search in $PATH by default.
PFEXEC-PATH
Path to the 'pfexec' binary, search in $PATH by default.
PFEXEC
If "NO" (the default), pfexec is not used, if set to "YES" then pfexec is used.
EXAMPLE
In this example, a dumptype is defined to use amzfs-snapshot script to create a snapshot and use amgtar to backup the snapshot.
define script-tool amzfs_snapshot {
comment "backup of zfs snapshot"
plugin "amzfs-snapshot"
execute-on pre-dle-amcheck, post-dle-amcheck, pre-dle-estimate, post-dle-estimate, pre-dle-backup, post-dle-backup
execute-where client
#property "DF-PATH" "/usr/sbin/df"
#property "ZFS-PATH" "/usr/sbin/zfs"
#property "PFEXEC-PATH" "/usr/sbin/pfexec"
#property "PFEXEC" "NO"
}
define dumptype user-zfs-amgtar {
dt_amgtar
script "amzfs_snapshot"
}
SEE ALSO amanda(8), amanda.conf(5), amanda-client.conf(5), amanda-scripts(7)
The Amanda Wiki: : http://wiki.zmanda.com/
AUTHORS
Jean-Louis Martineau <martineau@zmanda.com>
Zmanda, Inc. (http://www.zmanda.com)
Dustin J. Mitchell <dustin@zmanda.com>
Zmanda, Inc. (http://www.zmanda.com)
Amanda 3.3.1 02/21/2012 AMZFS-SNAPSHOT(8)