Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot... (7 Replies)
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Since the lost of the rtc all the settings became default. Does anyone remember what needs to be reset to discover both Hard drives? It sees the DVD and the scsi disk (intscsib.0) in 0/1/1/1.0 (disk 1 slot) but not 0/1/1/0.1 (intscsia.1)(disk 0 slot).
Right now, from the service menu, scsi shows... (3 Replies)
Discussion started by: mrmurdock
3 Replies
LEARN ABOUT PHP
prtvtoc
prtvtoc(1M) System Administration Commands prtvtoc(1M)NAME
prtvtoc - report information about a disk geometry and partitioning
SYNOPSIS
prtvtoc [-fhs] [-t vfstab] [-m mnttab] device
DESCRIPTION
The prtvtoc command allows the contents of the label to be viewed. The command can be used only by the super-user.
The device name can be the file name of a raw device in the form of /dev/rdsk/c?t?d?s2 or can be the file name of a block device in the
form of /dev/dsk/c?t?d?s2.
OPTIONS
The following options are supported:
-f Report on the disk free space, including the starting block address of the free space, number of blocks, and unused parti-
tions.
-h Omit the headers from the normal output.
-m mnttab Use mnttab as the list of mounted filesystems, in place of /etc/mnttab.
-s Omit all headers but the column header from the normal output.
-t vfstab Use vfstab as the list of filesystem defaults, in place of /etc/vfstab.
EXAMPLES
Example 1: Using the prtvtoc Command
The following example uses the prtvtoc command on a 424-megabyte hard disk:
example# prtvtoc /dev/rdsk/c0t3d0s2
* /dev/rdsk/c0t3d0s2 partition map
*
* Dimension:
* 512 bytes/sector
* 80 sectors/track
* 9 tracks/cylinder
* 720 sectors/cylinder
* 2500 cylinders
* 1151 accessible cylinders
*
* Flags:
* 1: unmountable
* 10: read-only
* * First Sector Last
* Partition Tag Flags Sector Count Sector Mount Directory
0 2 00 0 76320 76319 /
1 3 01 76320 132480 208799
2 5 00 0 828720 828719
5 6 00 208800 131760 340559 /opt
6 4 00 340560 447120 787679 /usr
7 8 00 787680 41040 828719 /export/home
example#
The data in the Tag column above indicates the type of partition, as follows:
Name Number
UNASSIGNED 0x00
BOOT 0x01
ROOT 0x02
SWAP 0x03
USR 0x04
BACKUP 0x05
STAND 0x06
VAR 0x07
HOME 0x08
ALTSCTR 0x09
CACHE 0x0a
RESERVED 0x0b
The data in the Flags column above indicates how the partition is to be mounted, as follows:
Name Number
MOUNTABLE, READ AND WRITE 0x00
NOT MOUNTABLE 0x01
MOUNTABLE, READ ONLY 0x10
Example 2: Using the prtvtoc Command with the -f Option
The following example uses the prtvtoc command with the -f option on a 424-megabyte hard disk:
example# prtvtoc -f /dev/rdsk/c0t3d0s2
FREE_START=0 FREE_SIZE=0 FREE_COUNT=0 FREE_PART=34
Example 3: Using the prtvtoc Command on a Disk Over One Terabyte
The following example uses uses the prtvtoc command on a disk over one terabyte:.
example# prtvtoc /dev/rdsk/c1t1d0s2
* /dev/rdsk/c1t1d0s2 partition map
*
* Dimensions:
* 512 bytes/sector
* 3187630080 sectors
* 3187630013 accessible sectors
*
* Flags:
* 1: unmountable
* 10: read-only
*
* First Sector Last
* Partition Tag Flags Sector Count Sector Mount Directory
0 2 00 34 262144 262177
1 3 01 262178 262144 524321
6 4 00 524322 3187089340 3187613661
8 11 00 3187613662 16384 318763004
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO devinfo(1M), fmthard(1M), format(1M), mount(1M), attributes(5)WARNINGS
The mount command does not check the "not mountable" bit.
SunOS 5.10 25 Jul 2002 prtvtoc(1M)