07-09-2009
What are the tickets you are dealing with asking you to do?
If you are replacing the card then you should observe anti-static precautions.
If this is Sun hardware then you need to note what the
local-mac-address? eeprom(1m) setting is set to because if it is set to true then it is using its own mac address if it is set to false then it is using the system's mac address.
On the operating system side then taking the network port down using
ifconfig(1m) will break your network connection to the system, not good it it is in a data centre miles away from your office!
10 More Discussions You Might Find Interesting
1. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
2. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
5. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
6. Ubuntu
hello,
first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me.
So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1.
but the traffic routing is nor working properly
i configured the 2 interfaces to be... (2 Replies)
Discussion started by: florin.bv
2 Replies
7. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
8. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
9. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
10. IP Networking
Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open).
I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give... (3 Replies)
Discussion started by: adrhc
3 Replies
HME(4) BSD Kernel Interfaces Manual HME(4)
NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device hme
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_hme_load="YES"
DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.
All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.
HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.
Cards supported by the hme driver include:
o Sun PCI SunSwift Adapter (``SUNW,hme'')
o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')
NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for
all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
address.
Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
add-on cards except the single-port SBus versions.
SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)
Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996,
http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf.
HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0.
AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.
BSD
June 14, 2009 BSD