07-09-2009
What are the tickets you are dealing with asking you to do?
If you are replacing the card then you should observe anti-static precautions.
If this is Sun hardware then you need to note what the
local-mac-address? eeprom(1m) setting is set to because if it is set to true then it is using its own mac address if it is set to false then it is using the system's mac address.
On the operating system side then taking the network port down using
ifconfig(1m) will break your network connection to the system, not good it it is in a data centre miles away from your office!
10 More Discussions You Might Find Interesting
1. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
2. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
5. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
6. Ubuntu
hello,
first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me.
So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1.
but the traffic routing is nor working properly
i configured the 2 interfaces to be... (2 Replies)
Discussion started by: florin.bv
2 Replies
7. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
8. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
9. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
10. IP Networking
Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open).
I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give... (3 Replies)
Discussion started by: adrhc
3 Replies
LEARN ABOUT MOJAVE
tc-matchall
Match-all classifier in tc(8) Linux Match-all classifier in tc(8)
NAME
matchall - traffic control filter that matches every packet
SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ]
DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
skip_sw
Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
face, operation will fail.
skip_hw
Do not process filter by hardware.
EXAMPLES
To create ingress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that
mirrors the packets to device eth2.
To create egress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
matchall filters on it that mirrors the packets to device eth2.
To sample one of every 100 packets flowing into interface eth0 to psample group 12:
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: matchall
action sample rate 100 group 12
SEE ALSO
tc(8),
iproute2 21 Oct 2015 Match-all classifier in tc(8)