07-09-2009
Reg- eth0,eth1 (ethernet card)
Hi Guys,
I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets.
10 More Discussions You Might Find Interesting
1. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
2. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
5. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
6. Ubuntu
hello,
first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me.
So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1.
but the traffic routing is nor working properly
i configured the 2 interfaces to be... (2 Replies)
Discussion started by: florin.bv
2 Replies
7. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
8. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
9. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
10. IP Networking
Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open).
I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give... (3 Replies)
Discussion started by: adrhc
3 Replies
LEARN ABOUT DEBIAN
aoe-discover
aoe-discover(8) System Manager's Manual aoe-discover(8)
NAME
aoe-discover - tell aoe driver to discover AoE devices
SYNOPSIS
aoe-discover
DESCRIPTION
The aoe-discover command tells the aoe driver to discover ATA over Ethernet (AoE) devices on the network. All network interfaces will be
probed with a AoE config query broadcast.
If the aoe-interfaces command has limited the allowable network interfaces, only devices discovered via allowable interfaces will become
available. The default is to make available all AoE devices found on all accessible ethernet networks.
It's good to run the aoe-discover command after running aoe-interfaces.
EXAMPLE
In this example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic. After remembering that
shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then calls aoe-discover
to ask the aoe driver to look for new AoE devices.
nai:~# modprobe aoe aoe_iflist="eth0"
nai:~# aoe-stat
e10.9 eth0 up
nai:~# aoe-interfaces eth0 eth3
nai:~# aoe-discover
nai:~# aoe-stat
e7.0 eth3 up
e7.1 eth3 up
e7.2 eth3 up
e7.3 eth3 up
e7.4 eth3 up
e7.5 eth3 up
e7.6 eth3 up
e7.7 eth3 up
e7.8 eth3 up
e7.9 eth3 up
e10.9 eth0 up
SEE ALSO
aoe-interfaces(8), aoe-stat(8), aoetools(8).
AUTHOR
Ed L. Cashin (ecashin@coraid.com)
aoe-discover(8)