07-09-2009
Reg- eth0,eth1 (ethernet card)
Hi Guys,
I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets.
10 More Discussions You Might Find Interesting
1. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
2. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
5. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
6. Ubuntu
hello,
first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me.
So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1.
but the traffic routing is nor working properly
i configured the 2 interfaces to be... (2 Replies)
Discussion started by: florin.bv
2 Replies
7. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
8. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
9. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
10. IP Networking
Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open).
I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give... (3 Replies)
Discussion started by: adrhc
3 Replies
LEARN ABOUT DEBIAN
mheard
MHEARD(1) Linux Programmer's Manual MHEARD(1)
NAME
mheard - display AX.25 calls recently heard.
SYNOPSIS
mheard [-d cmns] [-n] [-o cfpt] [-v] [port...]
DESCRIPTION
Mheard displays information about most recently heard AX.25 callsigns, the interface upon which they were heard, the total packets heard,
the time at which the last one was heard and other information. Mheard displays different information, in different orders depending on
the settings of the arguments. Information on specific ports can be displayed by giving the port names as arguments.
OPTIONS
-d cmns Sets the information that is displayed for each AX.25 callsign heard. The different arguments are:
c Display all the information with regard to callsigns, from-callsign, to-callsign, port name, and any digipeaters that may
be in use.
m Display miscellaneous information, the from-callsign, port name, no frames heard, the last type of frames heard, and
which different PIDs have been heard from that station.
n Display the default information. This is the from-callsign, port name, no frames heard and the date and time last heard.
s Displays statistics about the station heard, the from-callsign, port name, no I frames, no S frames, no U frames, time
first heard, and time last heard.
-n Supress the displaying of titles.
-o cfpt Sets the ordering of the information displayed. The meanings of the different arguments are:
c Sort list by from-callsign.
f Sort list by number of frames heard.
p Sort list by port name.
t Sort list by the time last heard, this is the default.
-v Display the version.
FILES
/var/ax25/mheard/mheard.dat
/etc/ax25/axports
SEE ALSO
ax25(4), mheardd(8).
AUTHOR
Jonathan Naylor G4KLX <g4klx@g4klx.demon.co.uk>
Linux 19 August 1996 MHEARD(1)