07-08-2009
Can you re-phrase your Q because it is not very clear. Got any use-case/examples for us?
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
in HPUX: I am copying oracle datafiles from one mountpoint to another
the total size is about 250Gb. I wanted to perform a checksum on the target and make sure the files came overy properly.
Mountpoints:
/s01 to /u01
/s02 to /u02
I tried using "SUM" on these mountpoints but its taking... (1 Reply)
Discussion started by: jigarlakhani
1 Replies
2. Filesystems, Disks and Memory
Hello,
I am performing a checksum on our software we have installed on a unix solaris 2.0 os.
If the checksum generated report is not the same as a 'Gold' report we have on disk. Then our software is deleted, and reinstalled.
The problem I am having is if you run the program again, the... (3 Replies)
Discussion started by: JustinPyfrom
3 Replies
3. SCO
Does anyone know the answer to this?
When I run "sum -r" on a file that I've down loaded from the sco website, the 1st set of numbers differs from the checksum on the download page but the
2nd set matches.
If I try to install the patch, I get errors.
Anyone has an answer? (3 Replies)
Discussion started by: jn5519
3 Replies
4. Programming
Hello Friends,
I'm constructing the IP Packets by using the RAW Sockets. If I give any value for VER/TTL/Protocol the packet is being transmitted with that particular values.
But in case of IP Checksum, I'm always getting the correct checksum value irrespective of the value I give.
Can anyone... (5 Replies)
Discussion started by: aamirglb
5 Replies
5. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
6. Solaris
Anyone can tell me the different between "cksum" and "sum" command on Solaris? I read the man pages but still not get it.
And how to display the md5 checksum for a file.
Thanks, (1 Reply)
Discussion started by: redstone
1 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
In file transfer with sftp protocol, what is the purpose "checksum" solves? Is this something not getting the file which has already been bought?
Waiting for your response !!! (1 Reply)
Discussion started by: sk84993
1 Replies
8. Solaris
Hello good people,
I came across md5 checksum. Can anyone please explain to me what it does and if possible an example of how to use it?
Thank you very much (1 Reply)
Discussion started by: cjashu
1 Replies
9. IP Networking
Hello
I am communicating with two devices using my computer over UDP protocol. The application is running fine. When I monitored the UDP traffic using Wireshark software, I found that there were too many Checksum errors.
Please find attached the png file showing this error. I am about to... (0 Replies)
Discussion started by: AustinCann
0 Replies
10. Solaris
Hi Guys,
I have about MD5 checksum so many times but I can't figure out how to use it. Can someone please show me how to perform an MD5 checksum?
Thanks a lot guys. (1 Reply)
Discussion started by: cjashu
1 Replies
LO(4) BSD Kernel Interfaces Manual LO(4)
NAME
lo -- software loopback network interface
SYNOPSIS
device loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
If the transmit checksum offload capability flag is enabled on a loopback interface, checksums will not be generated by IP, UDP, or TCP for
packets sent on the interface.
If the receive checksum offload capability flag is enabled on a loopback interface, checksums will not be validated by IP, UDP, or TCP for
packets received on the interface.
By default, both receive and transmit checksum flags will be enabled, in order to avoid the overhead of checksumming for local communication
where data corruption is unlikely. If transmit checksum generation is disabled, then validation should also be disabled in order to avoid
packets being dropped due to invalid checksums.
DIAGNOSTICS
lo%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
inet(4), intro(4)
HISTORY
The lo device appeared in 4.2BSD. The current checksum generation and validation avoidance policy appeared in FreeBSD 8.0.
BSD
March 15, 2009 BSD