07-08-2009
LOM ALOM ILOM ELOM RSC SP commands equivalent
Has anyone got an equivalent commands sheet for all Sun's serial or network management ports?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi , what are the ibm equivalent to the below commands. thanks
top
glance
ioscan (1 Reply)
Discussion started by: yls177
1 Replies
2. UNIX for Dummies Questions & Answers
Hi all
Can somebody tell me few emacs command for these:
#1.
How do I execute the last command in Emacs again. I mean Like the way one does in shell thru history or some other mechanism to do that. I am familiar withthe number argument. I mean if I have executed one command and after executing... (2 Replies)
Discussion started by: saurya_s
2 Replies
3. Solaris
I'm new in Sun, i just recieved a sun v100 server, i already connected the server to a workstation (using the hyperterminal tool) and it seemmed to be fine... however when the LOM> prompt appears and i try to introduce various commands but it does nothing.
LOMlite starting up.
CPU type:... (6 Replies)
Discussion started by: pasalagua
6 Replies
4. Solaris
Hello,
I need to run several command under LOM from unix shell.
the first command is resetsc -y and then I required to enter admin password.
Is there any way to make it with a script like:
#. <<LOM
resetsc -y
admin password
LOM
Is the password will accepted in that way ?
... (1 Reply)
Discussion started by: Alalush
1 Replies
5. Solaris
Hi,
Is it possible to manually set the sc/rsc netmgt port speed and duplex settings, rather than have it auto-negotiate?
How do you see what speed the port is currently connected at, from the host side (not from switch or router)?
Thanks (2 Replies)
Discussion started by: melias
2 Replies
6. UNIX for Advanced & Expert Users
Hi,
I have a problem when running some tests.
I unplug one power cable from the server.
No message is sent to/var/adm/messages
On the ILOM GUI, it shows power state deasserted.
Anyone knows how to forward this message to the OS, perhaps using the alert management settings? IPMI,snmp?... (1 Reply)
Discussion started by: ulemsee
1 Replies
7. Solaris
hi guys
How to know ILOM and ALOM ip address.
how to find the ilom alerts and alom alerts can one help out pls
thanks,
deepu.
---------- Post updated at 04:39 AM ---------- Previous update was at 04:38 AM ---------- (2 Replies)
Discussion started by: pradeepaasuri
2 Replies
8. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
9. Solaris
Hi, The system is Sun x4150. I use putty ssh to access to it. I can't start system console:
(hung)
Any help will be greatly appreciated! (5 Replies)
Discussion started by: aixlover
5 Replies
10. Solaris
Hi, I was trying to upgrade firmware for this Sun x4150 from ELOM to ILOM. I did it under GUI ELOM Manager > Maintenance > Firmware Upgrade. It then showed 'Someone is upgrading firmware' and took forever. I believe its hung due to unknown reason (wrong file used?). I poweroff and poweron the... (4 Replies)
Discussion started by: aixlover
4 Replies
SPIF(4) BSD Kernel Interfaces Manual SPIF(4)
NAME
spif -- SBus (spiffy) Serial/Parallel Interface
SYNOPSIS
spif* at sbus? slot ? offset ? (sun4c/sun4m/sun4u)
stty* at spif? (sun4c/sun4m/sun4u)
sbpp* at spif? (sun4c/sun4m/sun4u)
DESCRIPTION
The spif driver provides support for the Sun Serial/Parallel Interface card (Sun part number 501-1931), which is based on the Cirrus Logic
CD180 octal serial controller and the Cirrus Logic PPC2 parallel port controller.
The device minor numbers for this driver are encoded as follows:
+---+---+---+---+---+---+---+---+
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+---+---+---+---+---+---+---+---+
| | | | | | | |
| | | | | +---+---+---> port number
| | | | |
| | | | +---------------> unused
| | | |
| | | +-------------------> dial-out (on tty ports)
| | |
| | +-----------------------> unused
| |
+---+---------------------------> card number
Up to four cards are supported in the system.
Each of the serial ports has an 8 byte FIFO for receive and transmit as well as automatic hardware (RTS/CTS) flow control.
FILES
/dev/ttyS[0123][0-7] Serial ports
/dev/bppS[0-3] Parallel ports
DIAGNOSTICS
spif%d: ccr timeout A timeout occurred while writing to one of the CD180 registers.
stty%d-%d: ring overflow Incoming characters were discarded because the application in control of the device did not read the input fast
enough.
SEE ALSO
intro(4), sbus(4), tty(4)
HISTORY
The spif adapter was first supported in OpenBSD 2.5. The driver was ported to NetBSD 3.0.
AUTHORS
The driver was written by Jason Wright <jason@thought.net>, and is heavily based on the magma(4) driver written by Iain Hibbert.
TODO
The parallel port is not supported yet.
Dial-out (cua) devices are not yet supported.
BSD
February 4, 1999 BSD