07-07-2009
netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ---------- ---------
default 10.22.64.1 UG 1 6473
10.22.64.0 10.22.67.17 U 1 650 e1000g3301000
224.0.0.0 10.22.67.17 U 1 0 e1000g3301000
127.0.0.1 127.0.0.1 UH 48 1243248 lo0
10 More Discussions You Might Find Interesting
1. Cybersecurity
I am pretty new at running nmap ,and i have some doubt about some o/ps the nmap shows
I tried to scan my own system for UDP open ports
I see that if i use one UDP port say 13
It shows that its in open state , etc
But if i scan for the whole UDP ports in the nmap-services . I gives te... (2 Replies)
Discussion started by: DPAI
2 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Whenever I tried to run nmap on my linux (red hat 6.2) boxes i got these outputs:
4444/tcp filtered krb524
6666/tcp filtered irc-serv
6699/tcp filtered napster
8888/tcp filtered sun-answerbook
Can anybody please... (10 Replies)
Discussion started by: necro
10 Replies
3. Shell Programming and Scripting
Hi everyone!
I've temporarily come out of hibernation (and will be gone for about two weeks after this post too) to ask for input on a small PHP script I have just completed.
The script aims to be a remote front-end for Nmap - now for the safety of this post, I ask that any replies refrain from... (6 Replies)
Discussion started by: Karma
6 Replies
4. AIX
I'm trying to compile nmap 4.11 on an aix 5.2 machine and get the following error when attempting the 'make' command;
make
"Makefile", line 1: make: 1254-055 Dependency line needs colon or double colon operator.
"Makefile", line 14: make: 1254-055 Dependency line needs colon or double colon... (2 Replies)
Discussion started by: zuessh
2 Replies
5. Red Hat
Hi,
Is it possible to change the nmap port name: For eg:
21/tcp open ftp
53/tcp open domain
80/tcp open http
111/tcp open rpcbind
836/tcp open unknown
843/tcp open unknown
953/tcp open rndc
I need to change the port number 836 unknown to the name of the... (4 Replies)
Discussion started by: gsiva
4 Replies
6. Shell Programming and Scripting
So...
I'm trying to script and FTP Backup of some files from openVMS Alpha machine to a Unixware 7 machine.
I decided to use .netrc to do all the FTP actions however when I send the
nmap command. It pretty much gets ignored while even other things such "ascii", "case" etc.. get respected... (0 Replies)
Discussion started by: thesubmitter
0 Replies
7. Linux
Hi ,
I am exploring the nmap utility for Linux.
I know that, nmap binaries are specific to the platforms e.g. nmap binaries will be diferent for Windows , AIX , Solaris and Linux platforms.
Can anyone tell me , will the nmap binaries be different for different flavours of Linux such as... (1 Reply)
Discussion started by: jatin56
1 Replies
8. Solaris
Hello,
I am trying to install Nmap on my Solaris machine. I got errors at the very last of "make" command though. Could someone point me out what I am lacking?
Thank you!
Nmap version: 5.50 (nmap-5.50.tar.bz2)
Solaris version (cat /etc/release):
Error message ( run "./configure &&... (0 Replies)
Discussion started by: fragile_it
0 Replies
9. Cybersecurity
I'm seeing a persistent address showing up on my firewall router logs. The address is 10.98.115.9:67, and is broadcasting to 255.255.255.255. I know that this would typically signal a BOOTP service, such as a bootp server announcing itself on the network. But I can't isolate which machine it... (3 Replies)
Discussion started by: renoir611
3 Replies
10. Homework & Coursework Questions
Scripting language : Bash Shell Script
1. problem statement
I have to create function in which read IP addresses one by one from one file (iplist.txt) and scan these IP using nmap. This scan IP's output is saved in output.txt file and parse output.txt to save only open ports with particular IP... (3 Replies)
Discussion started by: sk151993
3 Replies
LEARN ABOUT OPENSOLARIS
inet_type
inet_type(4) File Formats inet_type(4)
NAME
inet_type - default Internet protocol type
SYNOPSIS
/etc/default/inet_type
DESCRIPTION
The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.
The inet_type file can contain a number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.
The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file. By default,
both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
setting the value of DEFAULT_IP. The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
will be displayed:
IP_VERSION4 Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
and netstat(1M) commands.
IP_VERSION6 Displays both IPv4 and IPv6 related information for ifconfig and netstat.
BOTH Displays both IPv4 and IPv6 related information for ifconfig and netstat.
The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For example,
even if the value of DEFAULT_IP is IP_VERSION4, the command
example% ifconfig -a6
will display all IPv6 interfaces.
EXAMPLES
Example 1 Suppressing IPv6 Related Output
This is what the inet_type file must contain if you want to suppress IPv6 related output:
DEFAULT_IP=IP_VERSION4
SEE ALSO
ifconfig(1M), netstat(1M)
SunOS 5.11 16 Jun 1999 inet_type(4)