Sponsored Content
Operating Systems Solaris Network interface configuration Post 302331550 by jenovaux on Monday 6th of July 2009 01:54:06 PM
Old 07-06-2009
thanks frozentin for your support but i done this command and all thing running good

cp -ir /etc/nsswitch.dns /etc/nsswitch.conf
svcadm enable svc:/network/dns/client:default
svcadm restart svc:/system/name-service-cache:default

but i have question for my experience
why solaris using NIS service is that any difference between NIS and DNS
like for Example
NIS is old version
i missing to understand the Difference between the two service {NIS - DNS}

thanks in advance
Jenova
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. Red Hat

wireless interface timeout configuration

Hello, I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies

3. Solaris

Solaris 19 10/09 ipv6 interface configuration

Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Discussion started by: pabloluja
3 Replies

4. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

6. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies

7. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
domainname(1M)						  System Administration Commands					    domainname(1M)

NAME
domainname - set or display name of the current domain SYNOPSIS
domainname [name-of-domain] DESCRIPTION
Without an argument, domainname displays the name of the current domain name used in RPC exchanges, usually referred to as the NIS or NIS+ domain name. This name typically encompasses a group of hosts or passwd entries under the same administration. The domainname command is used by various components of Solaris to resolve names for entries such as are found in passwd, hosts and aliases. By default, naming ser- vices such as NIS and NIS+ use domainname to resolve names. With appropriate privileges (root or an equivalent role [see rbac(5)]), you can set the name of the domain by specifying the name as an argument to the domainname command. The domain name for various naming services can also be set by other means. For example, ypinit can be used to specify a different domain for all NIS calls. The domain name of the machine is usually set during boot time through the domainname command by the svc:/system/iden- tity:domain service. If the new domain name is not saved in the /etc/defaultdomain file, the machine reverts to the old domain after it reboots. FILES
/etc/defaultdomain /etc/nsswitch.conf ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
nis+(1), nischown(1), nispasswd(1), svcs(1), hostconfig(1M), named(1M), nisaddcred(1M), sendmail(1M), svcadm(1M), ypinit(1M), sys-uncon- fig(1M), aliases(4), defaultdomain(4), hosts(4), nsswitch.conf(4), passwd(4), attributes(5), rbac(5), smf(5) NOTES
The domainname service is managed by the service management facility, smf(5), under the service identifier: svc:/system/identity:domain Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser- vice's status can be queried using the svcs(1) command. SunOS 5.10 7 Oct 2004 domainname(1M)
All times are GMT -4. The time now is 07:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy